Slew rate
Found 10 free book(s)A CAN Physical Layer Discussion
ww1.microchip.comThe decreased slew rate implies a slower CAN data rate at a given bus length, or a reduced bus length at a given CAN data rate. STANDBY Standby (or sleep) mode is entered by connecting the RS pin to VDD. In sleep mode, the transmitter is switched off and the receiver operates in a reduced power mode. While the receive pin (RXD) is still
NE5534 - Operational Amplifier, Low Noise, Single
www.onsemi.comload, slew rate, low overshoot, etc.). Features • Small-Signal Bandwidth: 10 MHz • Output Drive Capability: 600 , 10 VRMS at VS = 18 V • Input Noise Voltage: 4nV Hz • DC Voltage Gain: 100000 • AC Voltage Gain: 6000 at 10 kHz • Power Bandwidth: 200 kHz • Slew Rate: 13 V/ s • Large Supply Voltage Range: 3.0 to 20 V
NI 6351 Device Specifications - National Instruments
www.ni.comSlew rate 20 V/μs Glitch energy at midscale transition, ±10 V range 10 nV · s External Reference APFI 0 characteristics Input impedance 10 kΩ Coupling DC Protection, device on ±30 V Protection, device off ±15 V Range ±11 V Slew rate 20 V/μs 1 Typical behavior. Time period may be longer due to host system USB performance. Time period
50 µA, 2 mm × 1.7 mm WLCSP, Low Noise, Heart Rate …
www.analog.comSlew Rate . SR : 0.01 . V/µs . Voltage Noise Density (RTI) e. n . f = 1 kHz : 120 . nV/√Hz . Peak-to-Peak Voltage Noise (RTI) e n p-p : f = 0.1 Hz to 10 Hz . 7 . µV p-p . f = 0.5 Hz to 40 Hz . 9 . µV p-p . RIGHT LEG DRIVE AMPLIFIER (A2) Quiescent Supply Current . 7.5 . 10 . µA : Output Swing . R. L = 50 kΩ . 0.1 +V S − 0.1 . V . Short ...
MC33272A - Operational Amplifiers, Single Supply, High ...
www.onsemi.comHigh Slew Rate, Low Input Offset Voltage The MC33272/74 series of monolithic operational amplifiers are quality fabricated with innovative Bipolar design concepts. This dual and quad operational amplifier series incorporates Bipolar inputs along with a patented Zip−R−Trim element for input offset voltage reduction.
Operational Amplifier Circuits - MIT OpenCourseWare
ocw.mit.edureactive elements. Providing we keep the operating conditions out of the slew rate limit then this is a reasonable model. Here we wish to extend this picture of op amp operation to include circuits that are designed to be frequency dependent. This will enable the construction of active filters, integrators, differentiators and oscillators.
LT1010 - Fast ±150mA Power Buffer - Analog Devices
www.analog.comSlew Rate VS = ±15V, VIN = ±10V, VOUT = ±8V, RL = 100Ω 75 V/µs VSOS + Positive Saturation Offset IOUT = 0 (Note 5) l 1.0 1.1 V V VSOS – Negative Saturation Offset IOUT = 0 (Note 5) l 0.2 0.3 V V RSAT Saturation Resistance IOUT = ±150mA (Note 5) l 22 28 Ω Ω VBIAS Bias Terminal Voltage RBIAS = 20Ω (Note 6) l 700 560 840 880 mV mV IS ...
R XC2C32A CoolRunner-II CPLD - Xilinx
www.xilinx.comconfigurations include slew rate limit, bus hold, pull-up, open drain, and programmable grounds. A Schmitt trigger input is available on a per input pin basis. In addition to stor-ing macrocell output states, the macrocell registers can be configured as "direct input" registers to …
0 R XC9572XL High Performance CPLD - Xilinx
www.xilinx.com• Slew rate control on individual outputs • Enhanced data security features • Excellent quality and reliability - Endurance exceeding 10,000 program/erase cycles - 20 year data retention - ESD protection exceeding 2,000V • Pin-compatible with 5V-core XC9572 device in the 44-pin PLCC package and the 100-pin TQFP package
MCP4802/4812/4822 Data Sheet - Microchip Technology
ww1.microchip.comSlew Rate SR — 0.55 — V/µs Short Circuit Current ISC —15 24 mA Settling Time t SETTLING — 4.5 — µs Within 1/2 LSb of final value from 1/4 to 3/4 full-scale range Dynamic Performance (Note 2) DAC-to-DAC Crosstalk — <10 — nV-s Major Code Transition Glitch — 45 — nV-s 1 LSb change around major carry