6-0 RETENTION/DETENTION SYSTEMS - assets.ads-pipe.com

using either larger diameter corrugated polyethylene pipe and a shorter overall system length, or by using smaller diameter pipe and a longer system length. The final decision depends on the size of the site, its groundwater level, and cover requirements. Figure 6-2 shows a typical cross-section of a retention/detention system. Table 6-2

  System, Retention, Pipe, Detention, Corrugated, 6 0 retention detention systems

ADS N-12 WT IB PIPE (PER ASTM F2648) SPECIFICATION

Fittings Fittings shall conform to ASTM F2306. Bell and spigot connections shall utilize a welded bell and valley or saddle gasket meeting the watertight joint performance requirements of ASTM F2306. Field Pipe and Joint Performance To assure watertightness, field performance verification may be accomplished by testing in accordance with ASTM ...

  Specification, Astm, Fitting, Pipe, Watertight, Fittings fittings, Per astm f2648, F2648

ADS HP STORM 12”- 60” PIPE SPECIFICATION

Appropriate safety precautions must be used when field-testing any pipe material. Contact the manufacturer for recommended leakage rates. ... Backfill for minimum cover situations shall consist of Class 1 (compacted), Class 2 (minimum ... website at www.ads-pipe.com for a copy of the latest installation guidelines. Pipe Dimensions Nominal Pipe ...

  Installation, Testing, Pipe, Backfill

HP Storm Pipe

Installation shall be in accordance with ASTM D2321 and ADS recommended installation guidelines, with the exception that minimum cover in traffic areas for 12– through 48–inch (300 to 1200 mm) diameters shall be one foot (0.3 m) and for 60–inch (1500 mm) diameters, the minimum cover shall be 2 feet (0.6 m) in single run applications.

  Guidelines, Storm, Hp storm

ADS N-12 WT IB PIPE (PER AASHTO) SPECIFICATION

Material for pipe and fitting production shall be high-density polyethylene conforming with the minimum requirements of cell classification 424420C for 4- through 10-inch (100 to 250 mm) diameters, and 435400C

  Production, Pipe

ADS N-12 ST IB PIPE (ASTM F2648) SPECIFICATION

This specification describes 4- through 60-inch (100 to 1500 mm) ADS N-12 ST IB pipe (per ASTM F2648) for use in gravity-flow land drainage applications. Pipe Requirements ADS N-12 ST IB pipe (per ASTM F2648) shall have a smooth interior and annular exterior corrugations. • 4- through 60-inch (100 to 1500 mm) pipe shall meet ASTM F2648.

  Specification, Astm, Pipe, Per astm f2648, F2648, Astm f2648

N-12 ST IB Pipe (per AASHTO)

Pipe Requirements ADS N-12 ST IB pipe (per AASHTO) shall have a smooth interior and annular exterior corrugations. • 4- through 10-inch (100 to 250 mm) shall meet AASHTO M252, Type S or SP • 12- through 60-inch (300 to 1500 mm) pipe shall meet AASHTO M294, Type S …

  Pipe

Pure Basin & Curb Inlet Filters

Inlet Filters Pure basin and curb inlet filters are the preferred choice for permanent inlet protection and stormwater runoff control. Constructed of versatile stainless steel, Pure inlet filters will fit any drainage structure and are available with site-specific filter bags providing various levels of filtration. Applications • Car washes

  Stormwater, Filter

ADS SINGLE WALL PIPE SPECIFICATION

*Pipe O.D. values are provided for reference purposes only, values stated for 12 through 24-inch are ±1 inch. Contact a sales representative for exact values **All diameters available with or without perforations.

  Specification, Walls, Single, Pipe, Pipe o, Ads single wall pipe specification

ADS N-12 PLAIN END PIPE (PER ASTM F2648) SPECIFICATION

Installation shall be in accordance with ASTM D2321 and ADS recommended installation guidelines, with the exception that minimum cover in trafficked areas for 4- through 48-inch (100 to 1200 mm) diameters shall be one foot (0.3 m) and for 60-inch (1500 mm) diameter the minimum cover shall be 2 ft. (0.6 m) in single run applications.

SPRINKLER IRRIGATION Introduction Advantages of …

sprayed under pressure. This system is usually designed for relatively low pressure (1 kg/cm 2). The application rate ranges from 1.25 to 5 cm per hour for various pressure and spacing. Based on the portability, sprinkler systems are classified into the following types: (i) Portable system : A portable system has portable main lines, laterals and

  Pressure, Sprinkler, Low pressure

Motor Vehicle Air Conditioning (MVAC)

refrigerant (low pressure) to the ... to prevent refrigerant discharge when you connect or disconnect couplers. With proper charged\ and vehicle cold, the gauges should read close to 70 psi with a 70 degree ambient temperature. ...

  Pressure, Coupler, Low pressure

71 Series Hydraulic Quick Couplings High Pressure, Non ...

• Superior flow and low pressure drop ... High Pressure 71 Series Couplers Body Size Part Number Steel Port End Part Number 316 Stainless Steel Part Number High Pressure Stainless Steel Port End Length (in) Largest Dia. Wrench Flats 1/4 71-3C4-4F 1/4 - 18 NPTF S71-3C4-4F SH71-3C4-4F 1/4 - 18 NPTF 1.96 1.19 0.94

  Pressure, Coupler, Low pressure