Resistor packaging
Found 11 free book(s)Professional Thin Film Chip Resistors
www.vishay.comPACKAGING TYPE / SIZE CODE QUANTITY PACKAGING STYLE WIDTH PITCH PACKAGING DIMENSIONS MCS 0402 E5 5000 Paper tape acc. IEC 60286-3, Type 1a 8 mm 2 mm Ø 180 mm / 7" E0 10 000 MCT 0603 P5 5000 4 mm Ø 180 mm / 7" PW 20 000 Ø 330 mm / 13" MCU 0805 P5 5000 Ø 180 mm / 7" PW 20 000 Ø 330 mm / 13" MCA 1206 P5 5000 Ø 180 …
QPL MIL-PRF-55342 Qualified Thin Film Resistor, Surface ...
www.vishay.com• Antistatic waffle pack or tape and reel packaging available • Military / aerospace / QPL TYPICAL PERFORMANCE D3 3D 3D Models Adhesion Layer High Purity Alumina Substrate Nickel Barrier Solder Coating Passivation Resistor Film ABSOLUTE TCR 25 TOL. 0.1 STANDARD ELECTRICAL SPECIFICATIONS TEST SPECIFICATIONS CONDITIONS
Thick Film Chip Resistors (Low Resistance Type ... - Panasonic
industrial.panasonic.comCurrent sensing resistor Small size and lightweight Realize both low-resistance & High-precision by original thick film resistive element & special electrode ... Resistance value Packaging methods. Embossed carrier taping 4 mm pitch, 4,000 pcs. Punched carrier taping 2 mm pitch,10,000 pcs. 0603 0.5 W L08 1206 0.33 W L14 1210 0.33 W. Code Thick film
SURFACE MOUNT RESISTORS TECHNICAL GUIDE Ver
www.mouser.comPackaging material ∇. TECHNICAL GUIDE Ver.3 ... Where the resistor ids sealed and coated with resin, etc. (7). Where water or a water-soluble detergent is used in cleaning free soldering and in flux cleaning after soldering (Pay particular attention to water-soluble flux.) 8.2.Requests (1). This technical guide is summarized technical ...
general purpose 2%, 5% tolerance thick film chip resistor EU
www.koaspeer.comFor further information on packaging, please refer to Appendix A RK73B Type Size Nominal Resistance Tolerance Termination Material Packaging 2B T TD 102 J 2E (1210) Derating Curve 100 80 60 40 20-40 -20 0 60 80 100 120 140 160 70 125 Ambient Temperature (°C) 0-60-55 155 20 40 1F 1H, 1E, 1J, 2A, 2B, 2E, W2H, W3A (1W), W3A2 (2W) 1F (01005).015± ...
CF / CFM Series Stackpole Electronics, Inc.
seielect.comCarbon Film Resistor Stackpole Electronics, Inc. Resistive Product Solutions Current Noise: 2 The distance between flanges shall be 0.059 inches (1.50 mm) to 0.315 (8.00 mm) greater than the overall component. Packaging Specifications This is a non-critical dimension that does not have a tolerance in the standard.
74x Series - CTS Corp
www.ctscorp.comOptional tolerance at ±1% is available for all 741 - 745 package codes, 4-digit resistor codes; except 745X101 and 745X102 [±5% and ±1% only]. Consult factory for availability with 740X043 package code. Not all performance combinations and resistor values may be available. Resistor Value * Termination 10k ohm Matte Sn Finish
Thick Film Chip Resistors - Panasonic
industrial.panasonic.com【For Resistor】 *1: Use it on the condition that the case temperature is below the upper category temperature. *2: Rated Continuous Working Voltage (RCWV) shall be determined from RCWV=√Power Rating × Resistance Value,
precision 0.5%, 1% tolerance thick film chip resistor EU
www.koaspeer.comthick film chip resistor Maximum Working Voltage F±1% E-24, E-96* D±0.5% E-24, E-96 Part Designation Maximum Overload Voltage Operating Temperature Range Power Rating T.C.R. (x10-6/K) applications and ratings RK73H1H (0201) 0.05W 0.1W ±200 ±200 10Ω - 1MΩ 10 Ω - 10M * * 10Ω - 1MΩ 25V 50V-55°C to +125°C-55°C to +155°C Rated Ambient ...
LM567x Tone Decoder - TI.com
www.ti.com• R1 = Timing Resistor • C1 = Timing Capacitor (1) 10.3.2 Output Filter To eliminate undesired signals that could trigger the output stage, a post detection filter is featured in the LM567C. This filter consists of an internal resistor (4.7K-Ω) and an …
AT24C512C rev B Data Sheet - Microchip Technology
ww1.microchip.compins to a known state. When using a pull‑up resistor, Microchip recommends using 10 kΩ or less. 2.2 Ground The ground reference for the power supply. GND should be connected to the system ground. 2.3 Serial Data (SDA) The SDA pin is an open-drain bidirectional input/output pin used to serially transfer data to and from the device. The