PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: stock market

Basic Rigging Workbook - BNL

Basic Rigging Workbook Training and Qualifications Program Office October 13, 2008 - 2 - - 3 - Table of Contents Determine Task and Job-Site 4 Characterize the Load .. 7 Specify, Select, and Inspect Rigging 15 Wire Rope 15 Synthetic 19 21 Shackles .. 22 Eye 24 Hoist Rings .. 26 Turnbuckles .. 28 Using Rope in Rigging Applications .. 29 Lift, Maneuver, and Move Load .. 31 Handling Symmetrical Loads ..31 Handling Asymmetrical Loads ..32 Moving Loads through Vertical 33 Moving Loads through Horizontal 34 Moving Loads around or over Obstacles.

well as information from the Department of Energy's (DOE's) Hoisting and Rigging Manual and ANSI B30.9. Definitions Asymmetrical load. An object with an off-center center of gravity due to the object's irregular shape and/or composition. Critical lifts require confirmation of engineering, or merit additional engineering input

Fullscreen Download
Loading..

Tags:

  Rigging, Hoisting, Hoisting and rigging

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of Basic Rigging Workbook - BNL

Documents from same domain

Basic Rigging BNL Workbook 2008-10-13

training.bnl.gov

- 6 - If the lift has been classified as a pre-engineered lift, then additional criteria must be met prior to operation. If determined to be a critical lift, Plant Engineering riggers or an

Related documents

Training Requirements Chart - IHSA

www.ihsa.ca

hoisting operation of a device (platform, bucket, etc.) that is capable of moving and is supported by a cable attached to the boom Instructions about requirements, restrictions, and hazards of the hoisting operation IHSA offers Hoisting and Rigging—Basic Safety Training. Construction Projects, s.153(12) Worker who sets-up, assembles,

  Rigging, Hoisting, Hoisting and rigging

OSHA Subpart R: Steel Erection - Cleveland State University

academic.csuohio.edu

rigging assembly shall be set from the bottom up. 1926.753(e)(4)(iii) Rigged at least 7 feet (2.1 m) apart. Section 17 1926 Subparts R ... the hoisting line until the members are secured with at least two bolts per connection, of the same size and strength as …

  Steel, Rigging, Osha, Osha subpart r, Subpart, Steel erection, Erection, Hoisting

DNVGL-ST-0377 Standard for shipboard lifting appliances

rules.dnv.com

lifts (elevators), jacks, overhead drilling equipment, fork lifts, portable hoisting gear etc. 1.1.3.5 Personnel lifting with cranes otherwise designed for lifting of loads/cargo may be covered upon agreement. 1.1.3.6 Without prejudice to [1.1.2.4], deviations from the requirements given in this standard may only

  Hoisting

CRANE AND HOIST SAFETY PROGRAM

safety.caltech.edu

CCR TITLE 8 Group 13: Cranes and Hoisting Equipment The Crane and Hoist Safety Program is intended to: Ensure a safe work environment for personnel who operate, maintain, and/or work around cranes and hoists. Establish inspection procedures for cranes, hoists, chains, slings, etc.

  Hoisting

U.S. Army Corps of Engineers

www.publications.usace.army.mil

DEPARTMENT OF THE ARMY EM 385-1-1 U.S. Army Corps of Engineers CESO-ZA Washington, D.C. 20314-1000 For sale by the U.S. Government Printing Office

Related search queries

Hoisting, Hoisting and Rigging, OSHA Subpart R: Steel Erection, Rigging