CannonBall Sliding door cheat sheet - hgsitebuilder.com

Designed for wooden 2x4 or steel girts Available lengths: 8’-10’-12’-14’-16’-18’-20’ White Aluminum For 1.5” door. Use with stay roller & door stop Use with wood 2x4, 2x6 or steel girts Available lengths: 8’-10’-12’-14’-16’-18’-20’ White Painted Aluminum For 1.5” door. Designed for wooden 2x4, 2x6 or steel girts

  Trig

Fire Resistance Bulletin 2 - MBMA

Girts -"Z" or "C" shape girts fabricated from 0.056 to 0.120 in. thick steel. Girts shall be 6 to 10 in. deep with 2 ½ to 3 in. flanges. Girt Clips -Fabricated from min. 0.115 in. thick steel, angles may be bolted to columns with ½ by 1 ½ in. bolts and nuts or may be plates shop-welded to columns. Steel Wall Panels -No. 26 MSG min. coated steel.

  Trig

CLADDING ATTACHMENT SOLUTIONS FOR EXTERIOR …

Girts are spaced to line up with the stud framing behind (every 16” to 24” o.c.). Cladding is attached directly to the outer flange of the Z-girts. Where vertically oriented cladding is used, additional horizontal sub-girts may be applied to the exterior of the verticals.

  Solutions, Attachment, Exterior, Trig, Cladding, Cladding attachment solutions for exterior

Erection and Safety Manual - Armstrong Steel

12" Girts - BC-500 GIRT TO RAFTER CLIP Part #'s BC-15_ BC-16_ CEE RAKE TO PURLIN CLIP Part #'s 8" Cee Rake/8" Purlins - BC-18 10" Cee Rake/8" Purlins - BC-19 12" Cee Rake/8" Purlins - BC-20. Erection and Safety Manual Standard Parts Last Revision Date: 06/01/16 By: JMM 9 Page of 120 CEE RAKE RAFTER PEAK SPLICE SHEETING CLIP

  Erection, Trig

TYPES OF FRAMING - Construction Knowledge.net

Girts are usually 4 x 6 inches. With the exception of studs, braced frame members are heavier than those in balloon framing. Sills and corner posts are customarily 4 x 6 inches. Unlike the studs, corner posts extend from sill to plate. Knee braces, usually 2 x 4 inches, are placed

  Trig

Pole Barn Building Guide

and spacing of roof system, purlins, girts, beams and header sizes. 3. Indicate the locations of all window and door openings. 4. Indicate the locations of the poles, and provide dimensions between the poles. 5. Maximum width is 32’, max length 40’, maintaining at least a 5:3 length to width ratio. Section Elevation 1.

  Barn, Pole, Trig, Pole barns

zeds and cees user's guide - Lysaght Professionals

purlins and girts in a much wider range of spanning and bridging configurations than before. there has also been a rationalisation of coating mass. the data is intended for specifiers, engineers, builders and erectors for the specification, detailing and erection of lysaght purlin and girt systems. included are details of

  Trig

PREPARING FOR CHRISTMAS A Sermon By

''PREPARING FOR CHRISTMAS" INTRODUCTION One Sunday morning, a neatly dressed man disrupted a wor-sh.i.p service in a New York City church.Right in the mid­ dle of the service, this man stood up in the balcon,y and called out in a loud voice, "I have a word from the Lordi" Immediately the ewer-alert ushers sprang like gazelles up the balco~ stairs and ushered the …