PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: confidence

CHAPTER 8 CONSTRUCTION DETAILS - Progressive Materials

CHAPTER 8 CONSTRUCTION DETAILS provides technical information concerning the design and installation ofconstruction DETAILS for quality SPF roof systems. This introduction is intended to supplement the special notes on the individual CONSTRUCTION DETAILS are provided for the following SPFroof system types: SPF roof systems with protective coatings SPF re-cover roof systems with protective coatingsConstruction DETAILS applicable to SPF roof systems withprotective coatings are denoted as SPF- followed by anumber and possibly a letter ( , SPF-2, SPF-2A). CONSTRUCTION DETAILS applicable to SPF re-cover roof sys-tems with protective coatings are denoted as SPF(R)- followed by a number and possibly a letter ( , SPF(R)-1, SPF(R)-1A).The letter designation after an SPF roof system type des-ignation and number identifies NRCA s order of preferencefor addressing a specific detail condition. For example, CONSTRUCTION Detail SPF-3 Base Flashing With Coun-terflashing depicts NRCA s preferred method of address-ing a base flashing with counterflashing detail for SPFroof systems with protective coatings.

• Sheet-metal vents • Sheet-metal pitch pans • Through-wall flashings • Skylight components and flashings • Smoke hatch components and flashings • Expansion joints and related components • Wood blocking and attachment • Pipe or conduit supports • Crickets and saddles • Siding or cladding • Chimney caps • Wall cladding

Fullscreen Download
Loading..

Tags:

  Walls, Metal, Cladding, Wall cladding

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of CHAPTER 8 CONSTRUCTION DETAILS - Progressive Materials

Documents from same domain

COMPANY CREDIT POLICY - Progressive Materials

pmsilicone.com

A credit evaluation is performed by the Credit Department in order to recommend a credit line, payment terms, and any other conditions of sale specific to the customer. The proposal is submitted via analysis completed and signed off by the appropriate signature levels. Once approved an E-mail informing the Sales Representatives will be sent out,

  Policy, Analysis, Company, Direct, Company credit policy

Related documents

Valuation of properties in multi-storey, multi-occupancy ...

www.rics.org

∫ metal composite material (MCM) ∫ metal sheet panels ∫ rendered external wall insulation system ∫ plastic ∫ tiling systems and ∫ timber. Note: this list of cladding types is as defined by the UK government in Building Safety Programme: estimates of EWS1 requirements on residential buildings in England.

  System, Walls, Metal, Cladding

COLOUR CHART - Roof

www.roof.co.nz

management system, ensuring consistency and reliability. For peace of mind, insist on authentic ... refer to the New Zealand Metal Roof and Wall Cladding Code of Practice, available from metalroofing.org.nz. For installation, ... All standard* colours in the COLORSTEEL ...

  System, Standards, Walls, Metal, Cladding, Wall cladding

Curtain Wall Systems - Kawneer

www.kawneer.com

curtain wall systems have been designed and engineered to meet these demands and more. Our curtain wall systems have been tested and assessed in accordance with the relevant BS EN and Centre for Window and Cladding Technology (CWCT) Curtain Wall Standards. Curtain Wall Design Considerations Please note this is for guidance only 1.

  Walls, Cladding, Kawneer

INSTALLATION INSTRUCTIONS

versettastone.com

Set a standard Flat Panel into the Starter Strip on the adjacent wall. Slide the Universal Corner to extend past the wall edge and slide the standard Flat Panel to intersect with the Universal Corner. The standard Flat Panel side tongue will need to be removed. The Flat Panel can then tightly seat against the back of the Universal Corner.

  Standards, Walls, Panels

DuPont Weather Barrier Commercial Installation Guidelines

sweets.construction.com

exterior walls shall provide the building with a weather resistant exterior wall envelope. The exterior wall envelope shall include flashing, as described in Section 1405.3. DuPont™ Tyvek® Weatherization System products have been tested to the following standards. • ASTM E ®331 Standard Test Method for Water Penetration of Exterior Windows,

  System, Standards, Walls, Tyvek

Inspecting New Stucco and Lath Installations for Code ...

stuccoinstitute.com

tural panel, the whole wall becomes the framing member. We don’t require roofing contractors to lengthen their nails and only attach the shingles into the top truss chords. The roof dry-in essentially serves the same purpose as the wall dry-in when the finish is paint in stead of a colored cement finish coat. Remember, this application standard

  Standards, Walls, Panels

Axon Cladding Installation Guide

static-content-prod.jameshardie-digital.com.au

the front of the wall studs and directly behind the external cladding can cause installation issues and is thus not recommended. Flashing All wall openings, penetrations, intersections, connections, window sills, heads and jambs must be flashed prior to cladding installation. Accessories Some Scyon™ Axon™ cladding accessories may

  Walls, Cladding

HARDIPLANK Installation Instructions

www.structuretech1.com

construction, when the wall is furred out with wood fra-ming or minimum No. 20 gauge steel framing anchored to the wall. Framing can be spaced up to 24” OC. Consult National Evaluation Service report NER-405 for recog-nized applications to masonry block and wood or metal framing. A weather-resistive barrier * is recommended

  Walls, Metal

Related search queries

Metal, Wall, System, Cladding, Wall Cladding, Standard, Kawneer, Panel, Tyvek