PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: confidence

ELECTRIC CIRCUITS LABORATORY MANUAL

ELECTRIC CIRCUITS LABORATORY MANUAL (ECE-235 LAB) GUIDE LINES FOR THE EXPERIMENTS AND REPORT PREPARATION 1. Preparation for the experiment: Before conducting the experiment, the student is required to have read the experiment background and procedure from the experiment MANUAL and studied the related theory. The lab instructor may, during the experiment, ask students questions pertaining to the procedure and theory. The lab instructor may give negative points to and even prevent an unprepared student from conducting the experiment. Tardy students may not be allowed to perform the experiment. 2. LABORATORY teams: The class will be divided in teams of three or four students. The composition of the teams (which students will team up) is left to the preference of the students, but the lab instructor makes the ultimate decision as to each team's composition.

1- To introduce the students to the basic electrical equipments in the lab. 2- To be able to deal with some of the frequently used instruments and equipment; like the digital multimeter and DC Power supply. Introduction: DC Power Supply The DC power supply is used to generate either a constant voltage (CV) or a constant current (CC).

Fullscreen Download

Tags:

  Basics, Electric, Power

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of ELECTRIC CIRCUITS LABORATORY MANUAL

Documents from same domain

Lesson 11: Transformer Name Plate Data and Connections

www.engr.siu.edu

3/2/2018 1 LESSON 11: TRANSFORMER NAME PLATE DATA AND CONNECTIONS ET 332b Ac Motors, Generators and Power Systems 1 Lesson 11_et332b.pptx LEARNING OBJECTIVES

  Name, Data, Plate, Connection, Lesson, Transformers, Lesson 11, Transformer name plate data and connections

Lesson 15: Induction Motor Testing: Lock-Rotor and No-load ...

www.engr.siu.edu

Lock-rotor No-load DC Test V line = 36.2 V 460.0 V V dc = 12.0 V I line = 58.0 A 32.7 A I dc = 59.0 A P T = 2573.4 W P T = 4664.4 W Example 15-1 Solution (1) Lesson 15_et332b.pptx 10 Convert line voltages, currents and total power to per phase quantities

  Load, Dc load

Lesson 9: Practical Transformer Model and Calculations

www.engr.siu.edu

Typical values: 3-5% of rated for large power transformers. Transformer Voltage Drop and Impedance Lesson 9_et332b.pptx 18 Example 9-2: The equivalent resistance and reactance of a 50 kVA, 2400-480 V transformer's windings are R = 2.80 W and X = 6.00 W. (high side). A load of 10 20o is connected to the low voltage side. Determine:

  Transformers, Typical

ELECTRIC CIRCUITS LABORATORY MANUAL

www.engr.siu.edu

Tardy students may not be allowed to perform the experiment. 2. Laboratory teams: The class will be divided in teams of three or four students. The composition of the teams (which students will team up) is left to the preference of the students, but the lab instructor makes the

  Tardy

CHAPTER 1 THE SAFETY AND HEALTH MANAGER

www.engr.siu.edu

2004 Safety Lecture Notes Page 1 CHAPTER 1 THE SAFETY AND HEALTH MANAGER Everyone wants a safe and healthful workplace, but what each person is willing to do to ... committed for named target areas such as construction. Recordkeeping Forms . the safety and health manager.

  Lecture, Notes, Health, Safety, Construction, Manager, Lecture notes, The safety and health manager

Lesson 11: Transformer Name Plate Data and Connections

www.engr.siu.edu

Dot Notation - Terminals marked with a dot are considered instantaneously positive A B E AB + - + - N 1 N 2 I 1 I 2 0 degree shift C D Above Terminals A and C are positive at the same time E AB E CD 0 degrees Phasor Diagram TRANSFORMER MARKINGS AND POLARITY Lesson 11_et332b.pptx 4 A B + - E AB I 2 180 degree shift C D + -

  Connection, Terminal

Lesson 12: Parallel Transformers and Autotransformers

www.engr.siu.edu

Lesson 12_et332b.pptx 20 Autotransformer action can be obtained by proper connection of two winding transformer coils N 2 N 1 V HS Load For step-down mode LS 2 HS 1 2 N N N N N LS HS 2 1 2 LS HS V V N N N N N a Where: N1 = number of turns in primary (HV) N2 = number of turns in secondary (LV)

  Lesson

Lesson 14: Transfer Functions of Dc Motors

www.engr.siu.edu

10/28/2015 5 EXAMPLE 14-1 SOLUTION (2) 9 x c) Find maximum back emf Answer d) Find no-load motor speed At no-load, T=0. Load torque is zero. T=0 TRANSFER FUNCTION OF ARMATURE- CONTROLLED DC MOTOR 10 x Write all variables as time functions

  Load

CHARACTERISTICS OF PULSE AND SQUARE WAVES

www.engr.siu.edu

T ime A m p l i t u d e Definition : Pulse width, t p, is the time difference between the 50% amplitudes of the rising and falling edges. A A/2 t p t 1 t 2 Pulse Characteristics Positive and Negative Pulses Positive pulses increase from baseline voltage T ime A m p l i t u d e V baseline =0 V baseline >0

  Time, T ime

Lesson 22: Determining Control Stability Using Bode Plots

www.engr.siu.edu

TECHNOLOGY Lesson 22: Determining Control Stability Using Bode Plots 1 lesson22et438a.pptx Learning Objectives 2 lesson22et438a.pptx After this presentation you will be able to: List the control stability criteria for open loop frequency response. Identify the gain and phase margins necessary for a stable control system.

  Technology, Control

Related documents

ELECTRIC POWER SYSTEMS

personal.psu.edu

Electric power systems: a conceptual introduction/by Alexandra von Meier. p. cm. “A Wiley-Interscience publication.” Includes bibliographical references and index. ISBN-13: 978-0-471-17859-0 ISBN-10: 0-471-17859-4 1. Electric power systems. I. Title TK1005.M37 2006 621.31–dc22 2005056773 Printed in the United States of America 10 9876 543 21

  Electric, Power, Electric power

Related search queries

Electric power