PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: quiz answers

ELECTRIC CIRCUITS LABORATORY MANUAL

ELECTRIC CIRCUITS LABORATORY MANUAL (ECE-235 LAB) GUIDE LINES FOR THE EXPERIMENTS AND REPORT PREPARATION 1. Preparation for the experiment: Before conducting the experiment, the student is required to have read the experiment background and procedure from the experiment MANUAL and studied the related theory. The lab instructor may, during the experiment, ask students questions pertaining to the procedure and theory. The lab instructor may give negative points to and even prevent an unprepared student from conducting the experiment. Tardy students may not be allowed to perform the experiment. 2. LABORATORY teams: The class will be divided in teams of three or four students.

Squeeze the probes tightly so that good contact is established. Record the value of your body's resistance. 2. Considering that a current of 100-200 mA through your heart will almost certainly kill ... The measurement of the current and voltage are basic as other quantities can be

Fullscreen Download

Tags:

  Probes, Voltage

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of ELECTRIC CIRCUITS LABORATORY MANUAL

Documents from same domain

Lesson 9: Practical Transformer Model and Calculations

www.engr.siu.edu

Typical values: 3-5% of rated for large power transformers. Transformer Voltage Drop and Impedance Lesson 9_et332b.pptx 18 Example 9-2: The equivalent resistance and reactance of a 50 kVA, 2400-480 V transformer's windings are R = 2.80 W and X = 6.00 W. (high side). A load of 10 20o is connected to the low voltage side. Determine:

  Transformers, Typical

Lesson 15: Induction Motor Testing: Lock-Rotor and No-load ...

www.engr.siu.edu

Lock-rotor No-load DC Test V line = 36.2 V 460.0 V V dc = 12.0 V I line = 58.0 A 32.7 A I dc = 59.0 A P T = 2573.4 W P T = 4664.4 W Example 15-1 Solution (1) Lesson 15_et332b.pptx 10 Convert line voltages, currents and total power to per phase quantities

  Load, Dc load

CHARACTERISTICS OF PULSE AND SQUARE WAVES

www.engr.siu.edu

T ime A m p l i t u d e Definition : Pulse width, t p, is the time difference between the 50% amplitudes of the rising and falling edges. A A/2 t p t 1 t 2 Pulse Characteristics Positive and Negative Pulses Positive pulses increase from baseline voltage T ime A m p l i t u d e V baseline =0 V baseline >0

  Time, T ime

CHAPTER 1 THE SAFETY AND HEALTH MANAGER

www.engr.siu.edu

2004 Safety Lecture Notes Page 1 CHAPTER 1 THE SAFETY AND HEALTH MANAGER Everyone wants a safe and healthful workplace, but what each person is willing to do to ... committed for named target areas such as construction. Recordkeeping Forms . the safety and health manager.

  Lecture, Notes, Health, Safety, Construction, Manager, Lecture notes, The safety and health manager

Lesson 11: Transformer Name Plate Data and Connections

www.engr.siu.edu

3/2/2018 1 LESSON 11: TRANSFORMER NAME PLATE DATA AND CONNECTIONS ET 332b Ac Motors, Generators and Power Systems 1 Lesson 11_et332b.pptx LEARNING OBJECTIVES

  Name, Data, Plate, Connection, Lesson, Transformers, Lesson 11, Transformer name plate data and connections

Lesson 11: Transformer Name Plate Data and Connections

www.engr.siu.edu

Dot Notation - Terminals marked with a dot are considered instantaneously positive A B E AB + - + - N 1 N 2 I 1 I 2 0 degree shift C D Above Terminals A and C are positive at the same time E AB E CD 0 degrees Phasor Diagram TRANSFORMER MARKINGS AND POLARITY Lesson 11_et332b.pptx 4 A B + - E AB I 2 180 degree shift C D + -

  Connection, Terminal

ELECTRIC CIRCUITS LABORATORY MANUAL

www.engr.siu.edu

Tardy students may not be allowed to perform the experiment. 2. Laboratory teams: The class will be divided in teams of three or four students. The composition of the teams (which students will team up) is left to the preference of the students, but the lab instructor makes the

  Tardy

Lesson 12: Parallel Transformers and Autotransformers

www.engr.siu.edu

Lesson 12_et332b.pptx 20 Autotransformer action can be obtained by proper connection of two winding transformer coils N 2 N 1 V HS Load For step-down mode LS 2 HS 1 2 N N N N N LS HS 2 1 2 LS HS V V N N N N N a Where: N1 = number of turns in primary (HV) N2 = number of turns in secondary (LV)

  Lesson

Lesson 14: Transfer Functions of Dc Motors

www.engr.siu.edu

10/28/2015 5 EXAMPLE 14-1 SOLUTION (2) 9 x c) Find maximum back emf Answer d) Find no-load motor speed At no-load, T=0. Load torque is zero. T=0 TRANSFER FUNCTION OF ARMATURE- CONTROLLED DC MOTOR 10 x Write all variables as time functions

  Load

Lesson 22: Determining Control Stability Using Bode Plots

www.engr.siu.edu

TECHNOLOGY Lesson 22: Determining Control Stability Using Bode Plots 1 lesson22et438a.pptx Learning Objectives 2 lesson22et438a.pptx After this presentation you will be able to: List the control stability criteria for open loop frequency response. Identify the gain and phase margins necessary for a stable control system.

  Technology, Control

Related documents

High Voltage Differential Probes - Teledyne LeCroy

cdn.teledynelecroy.com

High Voltage Differential Probes HVD3605A, HVD3220, HVD3206A, HVD310xA The HVD3000A series high voltage differential probes provide high CMRR over a broad frequency range to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe,

  Probes, Voltage

Hall Effect Experiment - University of Tennessee

www.phys.utk.edu

A current I is arranged to flow through the strip from left to right, and the voltage difference between the top and bottom is measured. Assuming the voltmeter probes are vertically aligned, the voltage difference is zero when B = 0. The current I flows in response to an applied electric field, with its direction established by convention.

  Probes, Voltage

Nodal and Loop Analysis - Waterloo Maple

www.maplesoft.com

voltage of that source must also be expressed by the mesh currents. Examine the circuit ... Connect probes to the proper locations and ensure the 'v' option is checked on the 'Inspector' tab to ensure the voltage at each spot will be measured. Step 4 : Run Simulation

  Probes, Voltage

ELECTRIC CIRCUITS LABORATORY MANUAL

www.engr.siu.edu

Squeeze the probes tightly so that good contact is established. Record the value of your body's resistance. 2. Considering that a current of 100-200 mA through your heart will almost certainly kill ... The measurement of the current and voltage are basic as other quantities can be

  Probes, Voltage

Oscilloscope Probes:Theory and Practice

www.syscompdesign.com

The measurement voltage exceeds the range of the scope. You do not need a scope probe – and can use two separate leads or a shielded test cable (figure 4) – when: The circuit impedance is much less than the input impedance of the scope, and The frequencies being measured are low or accurate measurement of rise time is not important, and

  Probes, Voltage

P a g e | 1 USB2.0/3.2/BC1.2 Drop Droop Test for non-USB ...

www.usb.org

Measure the unloaded voltage of each port under test at the Vbus breakout and check the voltage level against that of the unloaded values in Table 1 and Table 2. If the voltage level is beyond the table limits the host or hub fails the test. 4.1.1.3 Drop test procedure for fully loaded setup with multimeter

  Voltage

User Guide M211060EN-J - Vaisala

www.vaisala.com

M211059EN Vaisala Humidity and Temperature Probes HMP60 and HMP110 Series Multilingual Quick Guide M210297EN Vaisala Handheld Humidity and Temperature Meter HM70 User Guide M211080EN Vaisala Mounting Flange for Humidity Probes Quick Reference Guide M211106EN Vaisala Loop Power Converter Quick Reference Guide 1.3 Documentation conventions

  Probes

Related search queries

Voltage, Probes