FEKO Examples Guide - Altair University

d Third party software licenses AcuConsole contains material licensed from Intelligent Light (www.ilight.com) and used by per-mission. Software Security Measures:

7 .0 Guide Example - Altair University

DIPOLE EXAMPLE A-1-2 Requesting calculations This problem is symmetric around the z=0 plane. All electric fields will be normal to this plane, and therefore the symmetry is …

  Dipoles

Solid Geometry Introduction Geometry Introduction

Title: Microsoft PowerPoint - HM_SolidGeom_Extract.pptx Author: rahulp Created Date: 20140209053511Z

  Geometry

-Introduction To Meshing Introduction ToMeshing

-Introduction To Meshing Introduction ... -Introduction To Meshing Types Of Elements Elements 1D 2D Mids urface y x t z t -thickness of plate t/2 ... CFD, or dynamic analysis ta kes a lot of time. K elements is necessa ry. • Ha rdware configuration and graphics ca rdcapacity of the available

  Introduction, Meshing, Introduction to meshing introduction

Chapter 1: HyperMesh Introduction - Altair University

HyperMesh Introduction: The User Interface • Graphics area – displays the model • Toolbar – Gives access to commonly used tools via icons • Pull Down Menu – places functionality into groups, accessible via pull downs • Menu Pages – divides the main menu into groups based on function • Main Menu – contains “panels ...

  Introduction

1D Elements - Altair University

Mar 01, 2017 · 5 In order to switch back to the HyperMesh GUI, just activate the icon in the upper left menu bar (beneath “Model”). Before we proceed creating a property collector we need to define a material (right mouse click in

  Elements, 1d elements

Chapter 2: Geometry Cleanup - Altair University

• Pinholes: Searches for closed loops of free edges (holes) within a surface Fills in the holes Leaves fixed point at the center • Surf Fillets: Searches for surfaces that act as fillet between other surfaces Tangentially extends them to form a sharp corner • Edge fillets: Searches for rounded corners on a surface

  Pinholes

- 2D Meshing 2D Meshing - Altair University

Feb 02, 2014 · analyze objects such as pressure vessels, or structures such as considered for pla te elements . You can apply the other ro tational nodal moments (except when about an axis normal to the element gr avit y, centrifug al and thermal loads are suppo rted . Su rface -based and elem ent prope rties (thickness, element normal coo rdina te,

  Pressure, Vessel, Load, Pressure vessel, Meshing, 2d meshing 2d meshing

Tutorial: Modal Analysis with Altair OptiStruct / HyperMesh

Modal Analysis with Altair OptiStruct / HyperMesh Some hints All components in the model must have material and properties assigned/defined. Make sure units are consistent and density is defined. (Example - if model is in mm for Steel then: Youngs Modulus = 210.000 MPa, Density = 7.9e-9 t/mm3) Modal analysis is typically a free or

  Analysis, Modal, Modal analysis

Geometry in HyperMesh - Altair University

On a clean 2D model consisting of surfaces, free edges appear only along the outer perimeter of the part and around any interior holes. Note: Free edges that appear between two adjacent surfaces indicate the existence of a gap between the two surfaces. The automesher will leave a gap in the mesh wherever there is a gap between two surfaces.

  Geometry

Getting Started: VISSIM

Lesson 1. Add a background image Lesson 2. Draw/Edit links Lesson 3. Draw Connectors and Turn Lanes Section 4: Add Vehicles 19

  Getting, Started, Getting started, Vissim

Implementing peak current mode control of a …

Implementing peak current mode control of a switch-mode power supply with a single microcontroller Introduction In the quest for higher efficiency in high wattage

  Dome, Control, Current, Implementing, Peak, Implementing peak current mode control

FEKO Examples Guide - Altair University

d Third party software licenses AcuConsole contains material licensed from Intelligent Light (www.ilight.com) and used by per-mission. Software Security Measures: