Fleck 5600 Service Manual
sysTem only and is noT inTended To TreaT waTer ThaT is ... Refer to the dimensional drawing for cutting height of the distributor tube. If there is no dimensional drawing, cut the ... 1.2 fluid ounce (35.5 ml) per cubic foot. B. Non-resinous exchangers; 0.8 fluid ounce (23.7 ml) per
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
IntelliFlo Variable Speed Pump Installation and User's ...
www.pentair.comCirculation systems operate under high pressure. When any part of the circulating system (i.e. locking ring, pump, filter, valves, etc.) is serviced, air can enter the system and become pressurized. Pressurized air can cause the pump housing cover, filter lid, and valves to violently separate which can result in severe personal injury or death.
SCREENLOGIC2 INTERFACE
www.pentair.comScreenLogic2® Interface User’s Guide vi About this User’s Guide This manual describes the how to set up and use the ScreenLogic2 ® Control System, including how to configure your IntelliTouch ® Control System using the Configurator utility, and how to use the ScreenLogic system program to control basic everyday pool and spa operations to advanced setup …
INSTALLATION AND USER’S GUIDE - pentair.com
www.pentair.comSolarTouch® Solar Control System Installation and User’s Guide ® SolarTouch Solar Control System Installation and User’s Guide i Most states and local codes regulate the construction, installation, and operation of public pools and spas, and the construction of
EASYTOUCH CONTROL SYSTEM 8 AND 4 FOR POOL AND SPA
www.pentair.cominstallations solid copper conductor between this unit and any metal equipment, metal enclosures or electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit. 5. The electrical supply for this product must include a suitably rated switch or …
iChlor Install and User's Guide - Pentair
www.pentair.comstorage. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. When using the iChlor Salt Chlorine Generator (SCG) with a Pentair Control System, always wire the iChlor Salt Chlorine Generator (SCG) Power Center to the pump side of the relay located in the
INTELLICHLOR POWER CENTER FOR USE WITH …
www.pentair.comoperation of public pools and spas, and the construction of residential pools and spas. It is important to comply with these codes, many of which directly ... should be connected to all metal parts of the swimming pool, spa, or hot tub structure and to all electrical equipment, metal conduit, and metal piping. ... A 10 AMP replaceable fuse is ...
HIGH PERFORMANCE PUMP
www.pentair.comtal Dynamic Head in Ft of Wa te r A B E C D F I H 0 20 40 60 80 100 120 140 160180 200220 240 260280300 PERFORMANCE CURVES KEY FEATURES ... Total HP or greater cannot be sold, offered for sale, or installed in a residential pool for filtration use in California, Title 20 CCR sections 1601-1609.
HIGH-PERFORMANCE HEAT PUMP
www.pentair.comHeat Pump. Heat pumps capture free heat in the air and transfer it to your pool water, making it one of the most energy efficient ways to heat your pool or spa. Compared to gas, oil, or electric heaters, the UltraTemp High Performance Heat Pump uses just a fraction of the energy to generate the same amount of heat. In fact,
IntelliConnect Installation Guide
www.pentair.comThis product is intended for use in swimming pool applications only. Most states and local codes regulate the construction, installation, and operation of public ... (1999). installation codes and ordinances must also be adhered to. ... Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and ...
FIBERGLASS SAND FILTER
www.pentair.comTriton® II Sand Filters The Triton II filter is the result of over 40 years of product evolution and refinement. It has set the industry standard for effectiveness, efficiency, long runs between service, and providing years of dependable, low maintenance operation. The Triton II filter features a special internal design that keeps the sand bed ...
Related documents
Failure of Cutting Tools and Tool Wear - IIT Kanpur
home.iitk.ac.inCutting fluid. Vibration behavior of the machine-tool work system. Built-up edge. Single-Point Tool Geometry. Tool Geometry: Rake Angle Increasing the Rake Angle reduces the cutting force and the cutting temperature resulting in increased tool life. However, for large rake angle, tool edge is weakened
Chapter 2 Pressure Distribution in a Fluid
dl.konkur.inFluid Mechanics 8th Edition White SOLUTIONS MANUAL. Chapter 2 • Pressure Distribution in a Fluid. P2.1 For the two-dimensional stress field in Fig. P2.1, let . Find the shear and normal stresses on plane . AA cutting through at 30°. Solution: Make cut ―AA‖ so that it just hits the bottom right corner of the element.
PROGRAMMER’S MANUAL I PROGRAM DESIGN AND …
www.cs.cmu.edu(4) there is cutting or grinding oil mist, (5) it may likely be submerged in fluid, (6) there is sulfuric cutting or grinding oil mist, or (7) there are any large-sized inverters, high output/high frequency transmitters, large contactors, welders, or other sources of electrical noise. 2.1.2 For dust-proof, splash-proof type
The Digestive System - Los Angeles Mission College
www.lamission.edu1.The parasympathetic nervous system increases pancreatic secretion 2. Two duodenual hormones also influence pancreatic secretion: Secretin and Cholecystokinin. 3. Food entering the small intestine stimulates the secretion of both hormones. 4. Secretin stimulates the secretion of pancreatic electrolyte –rich fluid , while CCK enhances the
Mission, System, Fluid, College, Angeles, Los angeles mission college
Cutting Fluids Manual - FUCHS
www.fuchs.comThe right cutting fluid – equally important as the right tool Choosing the right cutting fluid product for metalworking is a good example of minor details making a major difference. With the right cutting fluid you can reduce the number of unplanned stoppages, and increase the life of both the tool and the cutting fluid.
BOC Guidelines for Welding and Cutting
www.boc.com.au18.2 Straight Line and Bevel Cutting 53 18.3 Piercing and Cutting Holes 53 19.0 Nozzle Data Section 54 19.1 BOC Welding Tips 54 19.2 BOC 2 Seat Oxy-Acetylene Cutting Nozzles 54 19.3 BOC 2 Seat Oxy-LPG Cutting Nozzles 54 19.4 BOC 3 Seat Oxy-Acetylene Cutting Nozzles 55 19.5 BOC 3 Seat Oxy-LPG Cutting Nozzles 55 20.1 Equipment Care 56