TELESCOPE CONTROL SOFTWARE INSTRUCTION MANUAL

The optical tube on your Alt/Az telescope should be roughly level to the ground pointing due north. NOTE: All users should point the telescope north, regardless of whether they are in the Northern or Southern Hemisphere. Leveled mount and tripod For Northern and Southern Hemisphere users Pointing North and level Computerized EQ mount roughly ...

  Optical

2 22 CELESTIAL HIGHLIGHTS

january 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 19 20 21 22 23 24 25 26 27 28 29 30 31 april 2 3 4 6 7 8 9 10 11 12 13 14 15 17 18 19 20 21 22 23 24 25 26 27 28 29

TROUBLESHOOTING GUIDE

• Other operating systems should work but are untested CFM is delivered in a compressed archive (.ZIP) file. CFM ... manually install the required Prolific USB-Serial driver on your computer. In most cases, this driver will be automatically ... com/pages/technical-support for further assistance.

  System, Drivers, Assistance

2 22 CELESTIAL HIGHLIGHTS

JUN 21 - Summer Solstice SEPT 23 - September Equinox DEC 21 - Winter Solstice CONJUNCTIONS FEB 12 - Venus and Mars MAR 12 - Venus and Mars MAR 28 - Venus and Saturn APR 5 - Mars and Saturn APR 30 - Jupiter and Venus MAY 29 - Mars and Jupiter AUG 19 - Moon and Mars near Pleiades DEC 7 - Moon, Jupiter, Saturn, PARTIAL SOLAR ECLIPSE

  Winter, Solstice, Winter solstice

Complete Dovetail Jig Instructions

For half blind dovetail joints you will be using the 1/2" x 14º dovetail bit. Depth of cut will be 9/16" from the base of your router. Included on the half blind template is a gauge for setting this height (Fig. 3). Adjusting for joint tightness will be covered later in these instructions. A shop-built base allows for quick setup in the ...

  Dovetail, Dovetail jig

TECHNICAL SPECIFICATION TIKKA T3 LITE

OPTICAL SIGHT ATTACHEMENT 17mm dovetail rail METAL PARTS SURFACE FINISHING Blued metal parts STOCK Black synthetic stock TRIGGER MECHANISM Single stage trigger, adjustable pull 1 to 2kg (2 to 4 lbs) (Optional set trigger) SAFETY Two stage safety ACCESSORIES Manual SAKO LTD., P.O.BOX 149, 11101 RIIHIMÄKI, FINLAND,

  Dovetail

OPTICS - Leapers

2. Dovetail rail’s recessed stop pin holes.Turn the Cam Lever in the opposite direction to close the spring loaded locking plate, locking the QD mount base to the Picatinny rail. 3. Should the QD mount base be loose, unlock the Cam Lever and use the included Hex Wrench to adjust the Hex Screw found within the Cam Lever Housing. Turning

  Dovetail

BEFORE YOU BEGIN – SURFACE PREPARATION BEFORE YOU …

front panel and the dovetail on the side panel on both the left and right sides of the shed. DO NOT ENGAGE THE SNAPS. M Install Left Door Panel (K) inserting the lower hinge pin into Front Left Floor (A) socket, lift the left end of the Gable (M) enough to insert the top hinge

  Dovetail

TUNE GUITAR TO PITCH BEFORE TAKING MEASUREMENTS.

2. Break loose the neck dovetail bolts by half a turn 3. Make adjustment by accessing the intonation setscrew through the sound hole. Turning the setscrew clockwise will cause the guitar to play flat, turning it counterclockwise the guitar will play sharp. Note that one full rotation of the set screw will impact intonation by 2-3 cents 4.

  Taking, Measurement, Pitch, Before, Dovetail, To pitch before taking measurements

Instruction Manual - Meade Instruments

9. Dovetail Receiver (Not Visible) 10. Altitude Setting Circle and Lock 11. Optical Tube (OTA) 12. Dew Shield 13. Dust Cap (Not Shown) 14. Mount Body 15. Control Panel 16. Azimuth Setting Circle 17. Tripod Base with Mounting Knob 18. Tripod Leg 19. Accessory Tray Mounting Screw 20. Accessory Tray 21. Inner Support Struts 22. Tripod Leg Locks 23 ...

  Manual, Instructions, Instruction manual, Dovetail