IS 4251 (1967): Quality tolerances for water for processed ...
QUALITY TOLERANCES FOR WATER FOR PROCESSED FOOD INDUSTRY o. FOREWO RD 0.1 This Indian Standard was adopted by the Indian Standards Institution on 7 Aug~t 1967, after the draft finalized by the Water Sectional Committee had been approved by the Chemical Division Council. 0.2 In processed food industry, water is used for a number of purposes,
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
By Authority Of - Public.Resource.Org
law.resource.orgBy Authority Of THE UNITED STATES OF AMERICA Legally Binding Document By the Authority Vested By Part 5 of the United States Code § 552(a) and ... Specification for Line Pipe . 1 Scope . 1.1 PURPOSE AND COVERAGE . The purpose of this specification is to provide standards for pipe suitable for use in conveying gas, water, and oil in both ...
Specification, Line, Pipe, Authority, Specification for line pipe, By authority of
ASME B30.2-2005: Overhead and Gantry ... - Public.Resource.Org
law.resource.orgASME 830 STANDARDS COMMITTEE Safety Standard for Cableways, Cranes, Derricks, Hoists, Hooks, Jacks, and Slings (The following is the roster of the Committee at the time of approval of this Standard.)
By Authority Of - Public.Resource.Org
law.resource.orgBy Authority Of THE UNITED STATES OF AMERICA ... American Petroleum Institute. Recommended Practice for Analysis, Design, Installation, and ... nent is used in the process. The safety requirements of the individual process components may then be integrated into a complete platform safety system. The analysis procedures
American, Process, Safety, Institute, Authority, Petroleum, American petroleum institute, By authority of
By Authority Of - Public.Resource.Org
law.resource.orgACKNOWLEDGMENT . We are most grateful to the many manufacturers, fabricators and FGMA members who have given freely of their respective time and resources to make possible the 1990 Edition of the FGMA Glazing Manual.
ANSI A92.2: Vehicle Mounted Elevating and Rotating Work ...
law.resource.orgon vehicle-mounted elevating and rotating work platforms. The development and increasing use of such equipment had reached a stage where minimum specifications governing design and manufac
Vehicle, Mounted, Work, Platform, Elevating, Rotating, Vehicle mounted elevating and rotating, Vehicle mounted elevating and rotating work platforms
CHAPTER Classification of Buildings Based on Occupancy
law.resource.orgCHAPTER. Classification of Buildings . 2. Based on Occupancy . 2.1 Occupancy Classification 2.1.1. Every building or portion thereof and land-use shall be classified according to its use or ... the most hazardous area in a building shall govern its classification. This occupancy shall also
Chapter, Building, Classification, Occupancy, Occupancy classification, Chapter classification of buildings, Classification of buildings
EAS 260: Zippers — Glossary of terms - law.resource.org
law.resource.orgZippers — Glossary of terms 1 Scope This East African Standard covers terms or meanings used in the zipper industry. ... fastener, concealed — A slide fastener with the tapes folded so that on closure neither the slider body nor the fastener are visible from the outside of the article.
AA: Aluminum Construction Manual - Public.Resource.Org
law.resource.orgFOREWORD . This part of the Aluminum Construction Manual deals with speci fications for allowable stresses in structures. It . is a compilation of
Manual, Construction, Structure, Aluminum, Aluminum construction manual
ANSI B7.1: Safety Code for the Use, Care, and Protection ...
law.resource.org(This Foreword is nat a part of the American National Standard Safety Code ... as the ""American Standard Safety Code For the Use, Care and Protection of Abrasive Wheels." The Code has been revised in 1930, 1935, 1943, 1947. 1956, 1964 and 1970. ... Safety is indeed everybody's business in the "Use, Care and Protection of Abrasive Wheels."
Code, Standards, Protection, Safety, Care, National, Quot, And protection, The use, Safety code, Care and protection of, National safety code standard, Standard safety code, The quot use
ANSI Z89.1: Safety Requirements for Industrial Head Protection
law.resource.orgr Foreword (Thia Foreword i. not a part or American National Standard Sarety Requirement. ror Indultrial Head Protection. Z89.1·1969.l This standard is a partial revision o( American National Standard Safety Code (or Head. Eye.
Code, Industrial, Standards, Protection, Requirements, Safety, National, Heads, National standard, National safety code standard, Safety requirements for industrial head protection
Related documents
New South Wales Guide to Standards and Tolerances 2017
www.fairtrading.nsw.gov.auGUIDE TO STANDARDS AND TOLERANCES 2017. Disclaimer. The content in this Guide is based on technical standards and industry tolerances that describe (or refer to) what is considered an acceptable standard of finished workmanship in . home building construction. Please note that this is a guide only and that all other documents prescribing ...
Guide, Standards, Tolerance, Guide to standards and tolerances
Guide to Standards and Tolerances (currently under review)
www.vba.vic.gov.auThe Guide to Standards and Tolerances (the Guide) has been developed for use by builders and building owners as a convenient reference for acceptable standards of workmanship in domestic building construction. It is intended to address areas
Specifications and Tolerances for Reference Standards and ...
nvlpubs.nist.govtolerances useful. Use of these standards at all appropriate levels of manufacture, distribution, and Weights and Measures inspection will help promote accuracy and uniformity in commerce. The terms “weight”, “mass standard”, and “mass” as used in this publication refer to all sizes in
Standards, Specification, Tolerance, Specifications and tolerances for
ACI 117-10 Specification for Tolerances for Concrete ...
www.concrete.orgSpecification synopsis: This specification provides standard tolerances for concrete construction and materials. This document is intended to be used by specification writers and ACI committees writing standards as the reference document for establishing tolerances for concrete construction and materials.
General tolerances for Iinearand angular DIN dimensions ...
www.turkcadcam.netGeneral tolerances based on the tolerancing principle specified in ISO 8015 are only to be applied when the drawing concerned contains the reference 'Tolerancing to ISO 8015'. Where that is the case. the general geometrical tolerances (i.e. the tolerances of form and position) apply independently of the actual local sizes of the workpiece feature.
2015 Standard for Performance Rating of Water-chilling and ...
ahrinet.org91 Section H4 The table reference for operating condition tolerances must be changed to Table 12 instead of Table 11. This was a typo that must be corrected. Current sentence: Tolerances and stability requirements are defined in Table 11 in Section 5.6.2. New sentence: Tolerances and stability requirements are defined in Table 12 in Section 5.6.2.
General tolerances - 21food.cn
img.21food.cnThe use of general tolerances for size and geometry simplifies the task of ensuring that this prerequisite is met. 1 Scope This part of ISO 2768 is intended to simplify drawing indications and specifies general geometrical tolerances to control those features on the drawing which have no respective individual indication.