MATERIAL DATASHEET 17-4 PH Stainless Steel

17-4 PH Stainless Steel ADDITIONAL DATA Values listed below compare Markforged samples processed in three different ways: As-Sintered, heat treated to H900 standard, and heat treated to H1150 standard. These representative data were tested, measured, or calculated using standard methods and are subject to change without notice.

  Steel, 17 4

MATERIAL DATASHEET 17-4 PH Stainless Steel

17-4 PH Stainless Steel ADDITIONAL DATA Values listed below compare Markforged samples processed in three different ways: As-Sintered, heat treated to H900 standard, and heat treated to H1150 standard. These representative data were tested, measured, or calculated using standard methods and are subject to change without notice.

  Steel, 17 4

MATERIAL DATASHEET H13 Tool Steel - Markforged

Ultimate Tensile Strength ASTM E8 1420 MPa 1500 MPa 1580 MPa 0.2% Yield Strength ASTM E8 800 MPa 1250 MPa 1360 MPa Elongation at Break ASTM E8 5% 5% 14% Hardness ASTM E18 40 HRC 45 HRC 46 HRC Relative Density ASTM B923 94.5% 94.5% 100% Composition Amount Chromium 4.7-5.5% Molybdenum 1.3-1.7% Silicon 0.8-1.2% Vanadium 0.8-1.2% …

  Astm, 2015

Design Guide for 3D Printing with Composites - Markforged

process. Unless otherwise specified, data is based on parts printed on Markforged composite printers at 100 micron layer height in Onyx with default print settings. Minimum part dimensions X: 1.6 mm (0.063”) Y: 1.6 mm (0.063”) Z: 0.8 mm (0.031”) Minimum part size is limited to the extrusion width and height of each bead. The

  Based, Composite

MATERIAL SPECIFICATIONS COMPOSITES - …

markforged.com 85 School St, Watertown, MA 02472 COMPOSITES MATERIAL SPECIFICATIONS PLASTIC MATRIX Test (ASTM) Onyx Nylon Tensile Modulus (GPa) D638 1.4 0.94 Tensile Stress at Yield (MPa) D638 36 31

  Specification, Material, Composite, Material specifications composites

MATERIAL DATASHEET Composites

markforged.com 480 Pleasant St, Watertown, MA 02472 Composites MATERIAL DATASHEET Plastic Matrix Test (ASTM) Onyx Onyx FR Nylon W Tensile Modulus (GPa) D638 1.4 1.3 1.7 Tensile Stress at Yield (MPa) D638 36 29 51

MATERIAL DATASHEET 17-4 PH Stainless Steel - Markforged

Carbon 0.07% max Phosphorous 0.04% max Sulfur 0.03% max Iron bal Markforged H900 Heat Treated 17-4 PH stainless steel processed with the Markforged Metal X system heat treated to H900 specification. ASTM A564 H900 Heat Treated ASTM A564 17-4 PH stainless steel heat treated to H900 specification. MIM H900 Heat Treated

  Steel, Carbon, 17 4

Datasheet for Steel Grades Carbon Steel A572 Gr

Steel Bar Round Bar, Flat Bar, Square Bar Φ8-1200mm*L Forging, hot rolling and cold rolling, Cast Black, Rough Turning, Shot Blasting, Coil / Strip Steel Coil /Steel Strip 0.03-16.0x1200mm Cold-Rolled & Hot-Rolled Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting Pipes / Tubes Seamless Pipes/Tubes, Welded Pipes/Tubes OD:6-219mm x ...

  Grade, Steel, Carbon, Steel grades carbon steel