MA1454 Precision Sensor Signal Conditioner with ...

MA1454 Precision Sensor Signal Conditioner with Overvoltage Protection ˜˜ 19-5945 Rev 0; 6/11 General Description The MAX1454 is a highly integrated analog sensor

  With, Protection, Conditioners, Signal, Sensor, Overvoltage, Sensor signal conditioner with overvoltage protection

DS1558 Watchdog Clock with NV RAM Control

S1 s n, year 2000-compliant (Y2KC), real-time clock/calendar with an RTC alarm, watchdog timer, power-on reset, battery monitor, and NV SRAM controller.

  Watchdog

Not Recommended for New Designs - Maxim …

It is not recommended for new designs. ... compatible with the industry-standard LT1001. ... Precision Operational Amplifier

  Design, Operational, Precision, Recommended, Amplifier, Lt1001, Precision operational amplifier, Not recommended for new designs

MAX13487E/MAX13488E Half-Duplex RS-485-/RS …

MAX13487E/MAX13488E Half-Duplex RS-485-/RS-422-Compatible Transceiver with AutoDirection Control www.maximintegrated.com Maxim Integrated | 2 Absolute Maximum Ratings

  With, Control, Half, Transceiver, Compatible, Duplex, Duplex rs, 422 compatible transceiver with autodirection control, Autodirection

SCAN master - Maxim Integrated

0D[LP,QWHJUDWHG 5LR5REOHV 6DQ-RVH &$ 86$ Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product.

  Integrated, Maxim, Maxim integrated

A Channel Otpt an Controller - Maxim Integrated

Pin Description (continued) www.maximintegrated.com Maxim Integrated │7 MA31790 6-Channel PWM-utput Fan RPM Controller PIN NAME FUNCTION 9 TACH6

  Integrated, Maxim, Maxim integrated, Maximintegrated

DS2401 Silicon Serial Number - Maxim Integrated

This command allows the bus master to read the DS2401-bit family code, unique 48bit serial ’s 8 - number, and 8bit CRC. This command can only be used if there is a single DS2401 on the bus.

  Serial, Code, Number, Serial number

±15kV ESD-Protected, Slew-Rate-Limited, Low …

±15kV ESD-Protected, Slew-Rate-Limited, Low-Power, RS-485/RS-422 Transceivers SWITCHING CHARACTERISTICS—MAX481E/MAX485E, MAX490E/MAX491E, …

+12V, 30mA Flash Memory Programming Supply …

MAX662A _____Detailed Description Operating Principle The MAX662A provides a regulated 12V output voltage at 30mA from a 5V ±5% power supply, making it ideal for flash EEPROM programming applications.

M14 Six-Channel Digital Isolator - Maxim Integrated

MA14850 Six-Channel Digital Isolator Maxim Integrated 6 INSULATION AND SAFETY CHARACTERISTICS Note 2: All units are production tested at TA = +25°C. Specifications over temperature are guaranteed by design.

  Digital, Channel, Isolators, M14 six channel digital isolator, Six channel digital isolator

LTC6362 - Precision, Low Power Rail-to-Rail Input/Output ...

Differential Op Amp/SAR ADC Driver The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The LTC6362 draws only 1mA of supply current in active operation, and features a shutdown mode in which the current consump - tion is reduced to 70μA.

  Shutdown, Op amp

TPH2501/TPH2502/TPH2503 /TPH2504 3 P E A K 250MHz ...

shutdown current of only 1μA. The combination of high bandwidth, high slew rate, low power consumption and low broadband noise makes these amplifiers unique among rail-to-rail input/output op amps with similar supply currents. They are ideal for lower supply voltage high speed signal conditioning systems.

  Shutdown

2.7V to 5.5V Single Supply CMOS Op Amp

Oct 05, 2007 · family of low-power operational amplifiers (op amps) are offered in single (MCP601), single with Chip Select (CS) (MCP603), dual (MCP602), and quad (MCP604) configurations. These op amps utilize an advanced CMOS technology that provides low bias current, high-speed operation, high open-loop gain, and rail-to-rail output swing.

  Op amp

Low Noise Single-Ended to Differential - Analog Devices

The two op amp topology features very low noise op amps, that can support SNR >110dB in a 1MHz bandwidth. The input op amp is trimmed for constant low input-referred ... just 60µA in shutdown mode. The LT6350 is available in a compact 3mm × 3mm, 8-pin

  Devices, Analog devices, Analog, Shutdown, Op amp

Major Code Changes for 2020 NEC - PPRBD

The change here is that op en equipment doors cannot impede the entry to or egress from the working space. 3) 210.8 (A). ... Emergency Shutdown in One and Two Family Dwelling Units. ... be required for other than 125- volt 15 and 20 amp receptacles used in the recreational vehicle site equipment. 43) 600.4 (B).

  Shutdown

Battery Charging - Semiconductor company | TI.com

The op-amp amplifies the voltage drop across the 50 mΩ sense resistor (with a gain of 9.2) which locks the loop at the value of charging current that causes the output of the op-amp to be 1.23V. The resistor RTR is included to provide a "trickle charge" current when the LM2576 is turned off.

PIC16(L)F1704/8 Data Sheet

PIC16(L)F1704/8 DS40001715D-page 6 2013-2015 Microchip Technology Inc. TABLE 2: 20-PIN ALLOCATION TABLE (PIC16(L)F1708) I/O (2) PDIP/SOIC/ SSOP QFN ADC Reference Comparator Op Amp DAC Zero Cross Timers CCP PWM COG MSSP EUSART CLC Interrupt Pull-up Basic RA0 19 16 AN0 VREF- C1IN+ — DAC1OUT1 — — — — — — — — IOC Y …

  Op amp, Pic16, F1704 8, F1704

AVAILABLE Integrated Temperature Controllers for Peltier ...

Integrator Amp Open-Loop Gain A. OL-INT. R. LOAD = 10kΩ to REF 120 dB Integrator Amp CMRR CMRR. INT. 100 dB Integrator Amp Input Bias Current I. INT-BIAS. V. DD = 3V to 5.5V 1 nA Integrator Amp Voltage Offset V. INT-OS. V. DD = 3V to 5.5V -3 +0.1 +3 mV Integrator Amp Gain Bandwidth GBW. INT. 100 kHz Undedicated Chopper Amp Open-Loop Gain A. OL ...