Proof Load, Yield & Tensile Strength Chart - General Fasteners

Proof Load, Yield, & Tensile Chart GFC Engineering & Testing Center 1524 East 14 Mile Road • Madison Heights, MI 48071 • 248-307-0567 • www.genfast.com

  Proof, Load, Proof load

Minimum Thread Engagement (Bolt Failure) Chart - Standard

Minimum Thread Engagement (Bolt Failure) Chart - Standard 48 52.5 24 Nominal Diameter Stress Area Grade 2 Grade 5 Grade 8 Grade 2 Grade 5 Grade 8 Grade 2 Grade 5 Grade 8 (in) (in2) (in) (in) (in) (in) (in) (in) (in) (in) (in) 1/4 - 20 0.250 0.0318 0.14 0.23 0.29 0.13 0.21 0.27 0.29 0.47 0.58 5/16 - 18 0.313 0.0524 0.19 0.31 0.38 0.17 0.28 0.35 ...

  Standards, Thread

SAE and Metric Fastener Torque Specifications

Service Manual Supplement July 2016 Fastener Torque Specifications 4 SAE and Metric Fastener Torque Specifications SAE Plain and Zinc Plated Hex and Socket Head Cap ...

  Metrics

Torque-Tension Relationship for Metric Fasteners

Torque-Tension Relationship for Metric Fasteners ... The torque values can only be achieved if nut (or tapped hole) has a proof load greater than or equal to the bolt's minimum ultimate tensile strength. Clamp loads estimated as 75% of proof load for specified bolts.

  Metrics

ENGLISH/ METRIC BOLT SUBSTITUTION TABLE

Metric (millimeter) bolt and nut substitutions will be allowed in accordance with these tables. No substitution will be allowed for any A325 bolts supplied under §715-14 and used for structural connections on bridges, unless approved by the DCES. A-325 TYPE 3 A-449 TYPE 1 DIAM < 1.5" DIAM > 1.5" A-354 GRADE BD A-490 TYPE 1 A194 GRADE 2H

  Metrics

FASTENER SIZE CHART - Frontier Fastener

head markings - metric xx grade 5 cap screw grade 5 nut grade 8 nut xx grade 8 cap screw xx 8.8 class 8.8 cap screw class 8 nut class 10 nut 10.9 xx class 10.9 cap screw class 12.9 socket 8 10 alloy socket xx 12.9 material grade comparisons. created date: 11/13/2017 1:51:55 pm ...

  Metrics

Metric Nut Sizes - Bolt Depot

Metric Nut Sizes mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210. Title: metric-size-chart-nut Created Date: 2/16/2017 12:45:39 PM

  Bolt, Metrics, Depot, Bolt depot, Metric nut

Metric to Inch Conversion Chart - fastenerexperts.com

METRIC DIN 436 - Square Washer mm FRACTION DECIMAL DIN 439 A - Hexagon Nuts - 0,5d Unchamfered 3.5000 0.1378 DIN 439 B - Hexagon Nuts - 0,5d Chamfered 3.5719 9/64" 0.1406 DIN 444 A - Eye Bolts 3.9688 5/32" 0.1563 DIN 462 - Internal Tab Washers

  Metrics

Metric DIN 7984 Low Profile Head Hexagon Socket Cap Screws

Metric DIN 7984 are hexagon socket cap screws with a low profile head and are designed to be used where a reduced head height is of importance. Because of their reduced head height, the socket size is also reduced and as such cannot be ... Nut Load N/mm2 Austenitic 70 A2 and A4 50 500 70.000 <=M39 500 700100.000 <=M20 80 800 118.000 <=M20 800

  Metrics

Stainless Steel Seamless Tubing and Tube Support Systems ...

6 Weld nut 303 SS/DIN 1 .4305 SS 7 Weld plate 304 SS/DIN 1 .4301 SS 8 Mounting rail 303 SS/DIN 1 .4305 SS 9 Rail nut CF8M/DIN 1 .4408 SS 10 Strut nut Zinc-plated steel 316 stainless steel bolts and plates are available (see Bolted Plastic Clamp Support Options, page 8) .