PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: tourism industry

MMDVM Hotspot Configuration - ttci radio solutions

MMDVM Hotspot Configuration The ttci MMDVM Hotspot is a completely assembled MMDVM board over a Raspberry Pi Zero W and with Pi-Star software already installed. A few steps are needed however to get you online and on the air with the Hotspot . Initial Step One time Only I. WiFi Configuration by Creating a File (See section II for an alternative method to configure WiFi on your Hotspot ) Note: the MMDVM Hotspot only operates on WiFi due to the Raspberry Pi Zero W capability and requires a minimum of 2 Amperes DC 5V supply via USB. 1. Point your PC browser to 2. Select Country code (US or your specific county).

192.168.50.1) into the URL field • Once the Pi Star Dashboard is showing on the web browser, go to Configuration (username: pi-star and password: raspberry) • Scroll down to the Wireless Configuration section and click on Configure WiFi

Fullscreen Download

Tags:

  Configuration, Field

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of MMDVM Hotspot Configuration - ttci radio solutions

Related documents

Network Device Onboarding for Cisco DNA Center …

www.cisco.com

This includes entering device information and setting up a bootstrap configuration, full configuration, and Cisco device image for each device to be installed. The bootstrap configuration enables the PnP Agent, specifies the device interface to be ... Enter the building address in the text field under Address. Step 6. Click the Add button to ...

  Devices, Configuration, Cisco, Field, Cisco device

DX80 Performance Configuration Software Instruction Manual

info.bannerengineering.com

parameter contents are read from the Node and then the user changes one field, the tool only writes one field back to the Node. Default is ON—the configuration tool minimizes the data traffic. Use Legacy Commands for Device Communications—Older DX80 devices do not support access to device-level system parameters.

  Devices, Configuration, Field

Catalyst 3560-C and 2960-C Getting Started Guide (English)

www.cisco.com

For additional installation and configuration information for the switch, see the ... In the Switch Password field, enter your password. The password can be from 1 to 25 ... Use the device manager to perform basic switch configuration and monitoring. See the device manager online help for more information. 4.

  Devices, Configuration, Field

475 Field Communicator - Emerson Electric

www.emerson.com

Device interoperability is achieved through the Electronic Device Description Lang uage (EDDL) technology supported by the HART Communication Foundation and Fieldbus Foundation. Basic testing is performed on all device descriptions. Each device manufacturer is asked to certify that they thoroughly tested their devices with the 475 Field ...

  Devices, Field, Communicator, 475 field communicator

AN127: Flash Programming via the C2 Interface - Silicon Labs

www.silabs.com

The length of the WAIT field is controlled by the target device. During the WAIT field, the target device transmits 0’s on the C2D pin until it has finished writing to the target Data register. To indicate the write complete status, the target device transmits a 1 to terminate the WAIT field. AN127: Flash Programming via the C2 Interface C2 ...

  Devices, Field

NMEA 2000

www.nmea.org

Field # Field Description This network management message is used to claim network address, reply to devices requesting the claimed address, and to respond with device information (NAME) requested by the ISO Request or Complex Request Group Function. This PGN contains several fields that are requestable, either independently or in any combination.

  Devices, Field

HP Array Configuration Utility User Guide

h10032.www1.hp.com

3. Select Device Queries. 4. Under Device by Type, select All Servers. 5. Connect to the server that is running ACU. 6. Under Device Links, select the System Management Home Page. 7. Click Array Configuration Utility on the left-hand side of the screen. ACU opens, and identifies the controllers that are connected to the system. This

  Guide, Devices, Configuration, Utility, User, Array, Hp array configuration utility user guide

Hierarchal Testbench Configuration Using uvm config db

www.synopsys.com

Hierarchal Testbench Configuration Using uvm_config_db 2 Figure 1: set() and get() function syntax “cntxt” and “inst_name” are used to specify the storage location or address of the object handle. When used properly these parameters define the hierarchical path to the object data. “field_name” is the name for the object.

  Configuration, Field

AN758: Implementing USB Communication Device Class …

www.silabs.com

The USB communications device class (CDC) is a composite USB device class, and the class may include more than one interface. The CDC is used primarily for modems, but also for ISDN, fax machines, and telephony

  Devices, Communication, Implementing, Class, An857, Implementing usb communication device class

Related search queries

Device, Cisco, Configuration, Cisco device, Field, 475 Field Communicator, HP Array Configuration Utility User Guide, AN758: Implementing USB Communication Device Class