Draft Recommendations of the International Commission on ...

associated with nuclear or radiological event (IND/RDD). • Short briefings were provided for individual agencies by Jill Lipoti (State), Andy Wallo (DOE), and Mary Clark (EPA). Jill briefly summarized the current CRCPD ... Draft Recommendations of the International Commission on Radiological Protection, Author:

  International, Commission, Radiological, International commission, International commission on radiological

Technetium - 99m - University of Michigan

Exposure rates from unshielded 1.0 millicurie isotropic point source of Tc-99m: DISTANCE MILLIREM/HOUR 1.0 cm 760.00 10.00 cm 7.60 100.00 cm 0.076 6.0 in 3.270 Exposure Prevention ... • Monitor for removable surface contamination by smearing, swiping, swabbing, or wipe-testing where Tc-99m is used. Count smears or swabs in a liquid ...

  Surfaces, Unshielded, Technetium, Technetium 99m

Laboratory Ultraviolet Light Sources - Princeton University

UV levels in the actinic region for unshielded transilluminators. In conclusion, the authors stated: ... to shield the exposed surface of the transilluminator. No UV is detectable with the shield in place. A measurement with a UV radiometer indicated an exposure level of 200 µW/cm: 2

  Surfaces, Unshielded

H-MTD® High-Speed Modular Twisted-Pair Data Products

including Shielded Twisted Pair, Unshielded Twisted Pair and new High-Performance cables. ... 0M Surface mount device xx Blank cable group: 1 Crimp 4 PCB mounting: Successive number 1 Straight connector: 2 Right angle connector K Female jack: S Male plug W Tools: Z Plastic housings and accessories

  Surfaces, Unshielded

Heat Dissipation in Electrical Enclosures | Fan/Blower …

Enclosure Surface Area The physical size of the enclosure is the primary factor in determining its ability to dissipate heat. The larger the surface area of the enclosure, the lower the temperature rise due to the heat generated within it. To determine the surface area of an enclosure in square feet, use the following equation:

  Surfaces, Electrical, Heat, Enclosure, Dissipation, Heat dissipation in electrical enclosures

Technical Explanation for Proximity Sensors - Omron

The distance from the reference position (reference surface) to the measured operation (rese t) when the standard sensing object is moved by the specified method. Set Distance The distance from the reference surface that allows stable use, including the effects of temperature and voltage, to the (standard) sensing object transit position. This is

  Surfaces, Proximity

D-SUB CONNECTORS - Amphenol

Surface mount • Five shell sizes offer widest choice of contact positions: 9, 15, 25, 37 and 50 in standard density and 15, 26, 44, 62 and 78 positions in high-density. • Inserts are flame-retardant thermoplastic. • Accessories for all applications are available including strain reliefs, cable clamps, shielded backshells, mating hardware

  Surfaces, Connectors

Cytation™ 5 - University of Wisconsin–Madison

Operate the instrument on a level, stable surface away from excessive humidity. Bright sunlight or strong incandescent light can reduce the linear performance range of the instrument. Measurement values may be affected by extraneous particles (such as dust) in the microplate wells. A clean work area is necessary to ensure accurate readings.

  Surfaces, Cytation

Chapter 5 External Dose Calculations H-117 – Introductory …

Review ¾List the three methods of reducing your exposure/dose: ¾Intensity decreases _____ with the square of the distance from the source due only to the change in _____. H-117 – Introductory Health Physics Slide 31 ¾Using the inverse square law, calculate the dose rate at 4 feet away from a point source if the dose rate is originally 1000 R/hr at 2 feet.