PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: marketing

Part II How to Design and Build Working Electronic Circuits

2005 Hongshen Ma Part II How to Design and Build Working Electronic Circuits By Hongshen Ma 2005 Hongshen Ma Important note: This document is a rough draft of the proposed textbook. Many of the sections and figures need to be revised and/or are missing. Please check future releases for more complete versions of this text. 2005 Hongshen Ma Outline Part II How to Design and Build Working Electronic Circuits 11 Reading Datasheets 12 Electronic Packaging Through-Hole Surface Mount Ball Grid Array Comparing Packaging Technologies 13 Specifications of Discrete Components Resistors Capacitors Ceramic Capacitors Electrolytic Capacitors Tantalum Capacitors Diodes Transistors 14 Power supply Circuits Power supply Basics Bypass Capacitors Linear Voltage Regulators Switching DC-DC Converters 15 Understanding Op Amp Specifications Power supply Range Input and Output Voltage Range Input Offset Voltage Input Bias Current gain -Bandwidth Product Slew Rate

15.5 Gain-Bandwidth Product 15.6 Slew Rate 15.7 Equivalent Input Noise 15.8 Common-Mode Rejection Ratio 15.9 Power Supply Rejection Ratio 15.10 Rail-to-Rail 15.11 Single Supply 15.12 Settling Time and Stability 15.13 Quiescent Current Draw 15.14 Op Amp Packages 15.15 Sample Op Amps 16 Single Supply Op Amp Circuits

Fullscreen Download

Tags:

  Supply, Electronic, Gain, Single, Noise, Single supply

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of Part II How to Design and Build Working Electronic Circuits

Documents from same domain

Materials Data Book - University of Cambridge

www-mdp.eng.cam.ac.uk

1 CONTENTS Page Number Introduction 3 Sources 3 I. FORMULAE AND DEFINITIONS Stress and strain 4 Elastic moduli 4

  Data, Material, Book, Materials data book

Introduction to Octave - University of Cambridge

www-mdp.eng.cam.ac.uk

Introduction to Octave Dr. P.J.G. Long Department of Engineering University of Cambridge Based on the Tutorial Guide to Matlab written by Dr. Paul Smith September 2005 This document provides an introduction to computing using Octave. It will teach you howto use Octave to perform calculations, plot graphs, and write simple programs.

  Tutorials, Plot, Octave

Related documents

Designing and Building Transistor Linear Power Amplifiers

www.arrl.org

Part 2 — Apply techniques from Part 1 to single band HF and 6 meter linear amplifiers. Rick Campbell, KK7B 1Notes appear at the end of the article.. Figure 2 — A 37 dB gain linear amplifier. Figure 1 — Some MicroT2 applications. transmitted signal and noise and interfer-ence are low at the receiver. I’ve played that

  Gain, Single, Noise, Amplifier

Nonvolatile Memory, Dual 1024-Position Digital ...

www.analog.com

2.7 V to 5 V single supply or ±2.5 V dual supply . SPI-compatible serial interface . Nonvolatile memory stores wiper settings . Power-on refreshed with EEMEM settings . Permanent memory write protection . Resistance tolerance stored in EEMEM . 26 bytes extra nonvolatile memory for user-defined information . 1M programming cycles

  Supply, Single, Single supply

Capacitive Sensors

www.capsense.com

Jul 20, 2000 · between center and bottom plate. The amplifier circuit, depending on its configuration, can gen-erate a voltage proportional to C1 - C2 or C1/C2 or (C1 - C2)/(C1 + C2). This makes ratiometric measurements possible, where one capacitor is variable with motion and the other is fixed. Then

  Variable, Amplifier

Related search queries

Single, Gain, Amplifier, Noise, Single supply, Supply, Variable