POP Blind Riveting Systems
POP ® The POP ® rivet installation sequence is simple. 1. Place the mandrel of the POP ® rivet into the nosepiece of the setting tool. 2. Insert the POP ® rivet body through the hole of the materials to be fastened. 3. Pull the trigger of the setting tool. The POP ® Rivet body clamps the materials together and expands to form a secondary head on the blind side of the joint.
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Torx Plus Drive System - STANLEY® Engineered Fastening
www.stanleyengineeredfastening.comTORX PLUS Drive is a drive system designed to ensure optimum torque transmission and, ultimately, required clamp load. With a true 0° drive angle, the TORX PLUS system virtually eliminates the radial forces that can cause stress on fastener recesses. The elliptically-based geometric configuration of the TORX PLUS Drive System maximizes
www.StanleyEngineeredFastening.com www ...
www.stanleyengineeredfastening.comInsert, Screw Thread, Self Locking (Inch Series) NASM33537 Insert, Standard Dimensions, Assembly (Inch Series) NASM8846 Insert, Screw Thread, Helical Coil (Inch Series) MA1565 Insert, Screw Thread, Helical Coil (Metric Series) MA1567 Insert, Screw Thread, Helical Coil, Standard Dimensions, Assembly (Metric Series) MA3279, 3280, 3281
Hole Sizes for Cut Tapping - STANLEY® Engineered Fastening
www.stanleyengineeredfastening.com- 1 - stanleyengineeredfastening.com Chips Hole Sizes for Cut Tapping These charts are supplied as a recommendation only. Actual sizes may vary depending on application and the material being tapped.
Inserts - STANLEY® Engineered Fastening
www.stanleyengineeredfastening.comInsert, corrosion resistant Helical Coil Coarse Thread (Inch Series) NASM124651 thru NASM124850 Insert, corrosion resistant Helical Coil Fine Thread (Inch Series) NASM21209 Insert, Screw Thread, Self Locking (Inch Series) NASM33537 Insert, Standard Dimensions, Assembly (Inch Series) NASM8846 Insert, Screw Thread, Helical Coil (Inch Series) MA1565
Stud, Ferrule & Accessory Catalog
www.stanleyengineeredfastening.comMany studs, pins, anchors, and ferrules are featured to provide the greatest range of possible solutions to your stud welding applications. Bookmarks have been added to make navigation through the catalog quick and easy. Text explanations have been added to clarify some of the potential uses of each stud.
Catalog, Solutions, Ferrules, Dust, Accessory, Ferrule amp accessory catalog
Table of Contents
www.stanleyengineeredfastening.comHole Sizes for Cut Tapping 23 Hole Sizes for Cold Forming 24 Tap and Gage Part Numbers - English 25 Tap and Gage Part Numbers - Fractional 26 Tap and Gage Part Numbers - Metric 28 Gaging Recommended Gaging Practices 31 Standard Tap Dimensions 32 Tapping Troubleshooting 34 Application Profile 36 ...
2020 Stud, Ferrule & Accessory Catalog
www.stanleyengineeredfastening.com2020 Nelson® Stud Welding . Stud, Ferrule & Accessory Catalog . This catalog is designed to be a user-friendly source of information about the Nelson Stud Welding line of studs, anchors, pins, and the standard accessories used to weld them. Many features have been
Related documents
Selection Guide (Gripping Force) - Intelligent Actuator
www.intelligentactuator.comSelection Guide (Gripping Force) Selection Guide (Gripping Force) Keep the distance (L, H) from the finger (claw) mounting surface to the gripping point within the following range. If such distance does not fall within such range, excessive moment applies to the finger sliding parts and internal mechanism and the service life may be affected.
Guide, Selection, Force, Selection guide, Gripping force, Gripping
Parallel Type Air Gripper
content2.smcetech.comA gripping force of 24 N is obtained from the intersection point of gripping point distance L = 30 mm and pressure of 0.4 MPa. • The gripping force is 24.5 times greater than the workpiece mass, and therefore satisfies a gripping force setting value of 20 times or more. Step 1 Confirmation of Gripping Force Model Selection Illustration ...
ILO Glossary of Statistical Terms
www.ilo.orgQuick Guide on Sources and Uses of Labour Statistics . Business register – see Establishment register ... The sample size and sample selection methods for both outlets and the goods and services for which ... • gripping/holding difficulties (e.g., using fingers to g rip or handle objects)
A Guide to Selecting Non-Powered Hand Tools
www.cdc.govAwkward postures may cause you to use more force. Select a tool that can be used within the space available. For example, if you work in a cramped area and high force is required, select a tool that is held with a power grip. A pinch grip will produce much less power than a power grip. Exerting force with a pinch grip means you will work harder ...
810 Hand and Power Tool Safety - OSHAcademy
www.oshatrain.orgThis study guide is designed to be reviewed off-line as a tool for preparation to successfully complete OSHAcademy Course ###. Read each module, answer the quiz questions, and submit the quiz questions online through the course webpage. You can print the post-quiz response screen which will contain the correct answers to the questions.