PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: barber

STANDARD OPERATING PROCEDURE - OMMSWCC

STANDARD OPERATING PROCEDURE FORM ACTIVITY Drilling Operation SITE SMC DEPARTMENT Mining SOP NO. IMFA/SOP/SMC/MINING/01 REVISION 00 EFF DATE: NO. OF PAGES Page 1 Step No. Activity (WHAT) Associated Requirements/ Hazards/ Impact Process / tools / PPEs (HOW Responsibility (WHO)) Remarks / Refere 1 Pre start checking OH&S i)Fall i)Keep the ladders and handrails free from oil, grease and dirt(slippery condition ) . Drill Operator DOCNO. HIRA/MINING/01 Environment i)Air pollution(smoke) due to fire ii)Dust i-a)Remove cotton waste and extraneous material from the cabin.

spanner to the break out wrench and connect the other end to the wire sleeve of the drill. Open the break out wrench. Bit should get loosened by two/three pitch. If the chain spanner slips at the grip then tighten the adjusting bolt of the chain spanner and/or give a packing .Give reverse rotation to the rotary The bit will open.

Fullscreen Download
Loading..

Tags:

  Standards, Wrench

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of STANDARD OPERATING PROCEDURE - OMMSWCC

Documents from same domain

STANDARD OPERATING PROCEDURE

www.ommswcc.org

STANDARD OPERATING PROCEDURE FORM NO.HSE/CORP/4 ACTIVITY Excavation SITE SMC DEPARTMENT Mining SOP NO. IMFA/SOP/SMC/MINING/08 REVISION 00 EFF DATE: 19.6.14 NO. OF PAGES Page11 iv)Slip/Fall v)Vision problem vi)Strike to persons near by iv)Any spilled/ leaked oil is cleaned by cotton waste. v)Keep the cab. window clean so as to

  Operating, Standards, Procedures, Standard operating procedure

Related documents

National Standard Taper Pipe (NPT) Threads Size Chart

www.pyromation.com

National Standard Taper Pipe (NPT) Threads Size Chart 1/16 0.3125 27 0.16 0.2611 1/8 0.405 27 0.18 4½ 2½ 0.26 1/4 0.54 18 0.2 4 3 0.401 ... Wrench makeup turns Length of. effective thread Nominal size (inside diameter) Length of engagement (tightened by hand) Actual OD Threads per inch Hand tight turns.

  Standards, Wrench

Standard Operating Procedures of Hand Tools

www.tri-c.edu

Standard Operating Procedures of Hand Tools Introduction To safely use each tool in Ideation Station, follow the standard operating procedures below. Every hand tool in Ideation Station is listed and described in this document. If you are unsure ... Box Wrench Page 42. Spud Wrench Page 43. Adjustable Wrench Page 44. Socket Wrench

  Operating, Standards, Procedures, Tool, Hands, Wrench, Standard operating procedures of hand tools

STANDARD SERIES Badger 5 - InSinkErator

insinkerator.emerson.com

Self-service wrench. Available with or without a factory installed power cord. Warranty: 3-Year parts and in-home service. Sample Specification The complete InSinkErator warranty is included in the Care & Use Booklet packed with each uni.t * ... STANDARD SERIES FoodWaste Disposers

  Standards, Badger, Wrench, Badger 5

CAP SCREW HEAD WRENCH SIZE CHART - Imperial Supplies

www.imperialsupplies.com

Phone: 1-800-558-2808. imperialsupplies.com. CAP SCREW HEAD WRENCH SIZE CHART. Imperial has made a concerted effort to provide accurate information in its catalog and on its web site, however Imperial assumes no responsibility for the accuracy of the information.

  Wrench

Torque Range - Snap-on

www1.snapon.com

1994 and was calibrated on a torque standard traceable to the National Institute of Standards Technology (NIST). • Accuracy. All QD Series Torque Instruments are accurate to ±4% clockwise and ±6% counterclockwise from 20% of full scale to full scale. • Long Life Ratchet Head.QD Series Torque Instruments feature the Snap-on®

  Standards, Span, Snap on

Related search queries

Standard, WRENCH, Standard Operating Procedures of Hand Tools, Badger 5, Snap-on