PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: marketing

STANDARD OPERATING PROCEDURE - OMMSWCC

STANDARD OPERATING PROCEDURE FORM ACTIVITY Drilling Operation SITE SMC DEPARTMENT Mining SOP NO. IMFA/SOP/SMC/MINING/01 REVISION 00 EFF DATE: NO. OF PAGES Page 1 Step No. Activity (WHAT) Associated Requirements/ Hazards/ Impact Process / tools / PPEs (HOW Responsibility (WHO)) Remarks / Refere 1 Pre start checking OH&S i)Fall i)Keep the ladders and handrails free from oil, grease and dirt(slippery condition ) . drill Operator DOCNO. HIRA/MINING/01 Environment i)Air pollution(smoke) due to fire ii)Dust i-a)Remove cotton waste and extraneous material from the cabin. b)Check that Battery box / Fire prone area are free from Inflammable material.

9 Bit Grinding OH&S i)Eye injury i)Use safety goggles while grinding the bit. Drill Operator/ Drill Helper DOCNO. HIRA/MINING/01 Environment--Nil Quality-i)Grinding of drill bit i)Place the grinding table near the receiver tank of drill machine …

Fullscreen Download
Loading..

Tags:

  Machine, Drill, Grinding, Drill machine

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of STANDARD OPERATING PROCEDURE - OMMSWCC

Documents from same domain

STANDARD OPERATING PROCEDURE

www.ommswcc.org

STANDARD OPERATING PROCEDURE FORM NO.HSE/CORP/4 ACTIVITY Excavation SITE SMC DEPARTMENT Mining SOP NO. IMFA/SOP/SMC/MINING/08 REVISION 00 EFF DATE: 19.6.14 NO. OF PAGES Page11 iv)Slip/Fall v)Vision problem vi)Strike to persons near by iv)Any spilled/ leaked oil is cleaned by cotton waste. v)Keep the cab. window clean so as to

  Operating, Standards, Procedures, Standard operating procedure

Related documents

UNIT 1 INTRODUCTION TO TOOL Introduction to Tool ...

www.nitc.ac.in

The machine tool that is able to perform all the metal cutting operations within their range of operation is called as general purpose machine tool. These are also called basic machine tool. Examples of general purpose machine tools are engine lathe, drilling machine, milling machine, boring machine, grinding machine, shaping and planing machine

  Introduction, Machine, Tool, Grinding, Grinding machines, Introduction to tool introduction to tool

GRINDING MACHINES - Carnegie Mellon University

uhv.cheme.cmu.edu

The bench-type drill grinding machine is intended for drill sharpening. The accuracy of this type of grinder is not dependent on the dexterity and skill of the operator because the drill is placed in a holding device. The holding device places the drill in the correct position for the clearance and

  Machine, Drill, Grinding, Drill grinding machine

Safeguarding Equipment and Protecting Employees from ...

www.osha.gov

Specific Machine Hazards and Safeguarding Methods 20 Hazards of Mechanical Power Presses 20 ... cutting band saws, drill presses, milling machines, grinding machines, and slitting machines. The information in this booklet does not specif-ically address amputation hazards on …

  Machine, Drill, Grinding

Toolbox Talk #14 MACHINE GUARDING

www.ehs.harvard.edu

MACHINE GUARDING Environmental Health, Safety & Emergency Management Cambridge Campus 46 Blackstone St. Cambridge MA, 02139 (617) 495-2060 Longwood Campus ... Drill Press Grinding Wheels Mechanical Power Press Mortising Machine Retro-Fit all non com-pliant equipment . Author:

  Machine, Drill, Grinding

Machining Processes - University of Rhode Island

personal.egr.uri.edu

•Machine tool –design, stiffness & damping, structure ... • Creating a hole in a workpiece by mounting a drill bit on the tailstock ... drilling, boring, and them reaming, as well as possibly honing or grinding to improve internal surface and deburring the tool exit surface of through holes • Holemaking is a major cost of components ...

  Machine, Drill, Grinding

LABORATORY MANUAL - IIT Kanpur

home.iitk.ac.in

Grinding 2. Boring 2. Drilling 2. Lapping 3. Shaping 3. Tapping 3. Honing 4. Planing 4. Reaming 4. Super-finishing 5. Hobbing 6. Broaching 7. Sawing The process of chip formation in metal cutting is affected by relative motion between the tool and the workpiece achieved with the aid of a device called machine tool.

  Machine, Grinding

The DIY STEN Gun - noblogs.org

elcombate.noblogs.org

later on in WW2, so even a fairly soft 'machine-able' or 'leaded' grade of mild steel bar stock is perfectly suitable. The centre of the bolt is first marked and drilled using a 10mm drill bit until 3mm deep. This is best achieved using a number of smaller drill bits starting at 6mm. If misalignment is

  Machine, Drill

STANDARD OPERATING PROCEDURES for COMMON …

www.mcgill.ca

• Stop the machine immediately if odd noise or excessive vibration occurs. • Only properly sharpened drill bits and cutting tools in good condition should be used. Dull drill bits and chipped or broken cutting tools must be removed from service. • Disconnect the lathe from power source, Lock-out/Tag-out, if making repairs or servicing.

  Operating, Standards, Machine, Procedures, Common, Drill, Standard operating procedures for common

Drill Nomenclature and Geometry - NEMES

neme-s.org

Drill Nomenclature-Points• Elements of Drill Points • Lip Relief Angle – Varies with the diameter of the drill and hardness of the material – On larger diameters and drills for harder materials, lip relief is decreased to as low as 8° – Drills for soft materials and small diameters have high relief angles up to 24° – Lip relief angles are measured across the margin

  Drill

Related search queries

INTRODUCTION TO TOOL Introduction to Tool, Machine, Grinding machine, Grinding, Drill grinding machine, Drill, STANDARD OPERATING PROCEDURES for COMMON