PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: confidence

www.nikkostirling

EN. Locking ring Objective Parallax Adjustment Scope tube Turret cap Elevation Windage Magnification Illumination Adjustment Ocular Fast Focus ring 4. Congratulations on the purchase of your new Nikko Stirling riflescope. Please read this manual before mounting your Nikko Stirling scope for proper and safe use. All Nikko Stirling scopes are shock- and fog proofed and feature coated lenses combined with perfect optical calculation. Engineered, constructed and designed for hunters and marksmen. 1. FOCUSING. CAUTION: Viewing the sun can course serious eye injury. Never look at the sun with this product or even with naked eye. Turn the fast focus ring on the end of ocular in or out for adjustment. 2. MOUNTING. CAUTION: Be sure gun is not loaded. Use safe gun handling procedures. Separate the tops of the rings from the bottom portion.

aligned with the bore axis, tighten the ring tops. CAUTION: Do not overtighten. Overtightening can cause damage to the scope, affecting performance or even rendering it inoperable. There should be a slight gap between the rings. The gaps should be even on the left and right side of both rings. 3. PRE-ZEROING CAUTION: Be sure gun is not loaded.

Fullscreen Download
Loading..

Tags:

  Ring

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of www.nikkostirling

Related documents

SKF Universal Joints/Crucetas/Joints de cardan

www.skf.com

joints with similar bearing diameter, next check lube itting footnote or the lock-up type. Use the series column to refer to the proper series section of the catalog for related components (yokes, etc.) if necessary. How to use this catalog—Universal joint identiication Round Inside Lock-Up/Snap Ring (ISR)

  Ring, Check, Proper

Check for Proper Ring End Gap - Wiseco

www.wiseco.com

Check for Proper Ring End Gap Failure to ensure proper ring end gap may cause the ring tips to butt, and engine damage could occur. 1. A torque plate should be attached to the engine block or cylinder (if applicable), and torqued to specifications. 2. Check the end gap by placing the ring into the cylinder. Cylinder bore should be free of taper.

  Ring, Check, Proper, Check for proper ring end gap, Proper ring end gap, End gap

Series 2100 Brochure - EBAA

ebaa.com

4. Place the O-ring into the groove of the 2100 Gasket Ring. (This step may have been completed at the factory, check Gasket Ring to see if O-ring is already in place.) Place the Gasket Ring on the pipe with the O-ring facing the pipe end and the gasket recess facing the EBAA-Seal (or transition) Gasket and restraint ring…

  Ring, Check

John Deere 310 Tractor Loader Backhoe Service Manual

www.jensales.com

Check start-safety switch operation. Check battery voltage when starting. Check operation of alternator and oil pressure indicator lights. Carburetor mixture Dynamometer Test Transm iss ion-Reverser Check shifting. Check for proper operation without excessive noise. Check differential lock operation. Check brake pedal travel and even position.

  Services, Manual, Check, Proper, Deere, Tractors, Backhoe, Loaders, Deere 310 tractor loader backhoe service manual, Check for proper

ERIKS - Technical Manual - O-Ring Gland Design Information

o-ring.info

the O-ring, causing friction and heat. Because rubber is a poor conductor of heat, the O-ring can loose its proper-ties. To minimize or reduce wear, the following could be done; however consult the local ERIKS representative: • confirm amount of squeeze. • use the smallest possible cross section. • select an O-ring with internal lubri-

  Ring, Proper

Installation Instructions - Watts

media.wattswater.com

wise to break the sleeve O-ring seals. Using the screwdriver, slowly slide the cover sleeve to the downstream side of the housing. (Figure B) 3. Remove the stainless steel check retainer from the housing. (Figure B) 4. Remove the #1 check module (Figure C) by inserting two flat blade screwdrivers into the slots on either side of the check

  Ring, Check, Watt

S-Cam Air Brakes - Trailer Parts 4U

www.trailerparts4u.com

diameter shoe web holes near the camshaft roller end of the shoe. 8. Install retractor spring between shoes. Place top shoe onto spider as in service. Pivot bottom shoe on the camshaft head and twist the shoe 90° under the spindle, properly placing shoe on the spider as in service. 9. Install two (2) keeper springs on the anchor end of the ...

  Brake, S cam air brakes

Quality Procedure QP158 Thread Inspection

www.flexial.com

5.3.2.1. Use a CMM, comparator, or vision system to check the root radius on external threads. 5.3.3. Checking the Pitch Diameter of Threads Using GO and NOGO Thread Ring Gages 5.3.3.1. The use of the GO gage must allow for free acceptance. This means minimal force

  Ring, Check

ENGINEERING ETHICS

ethics.tamu.edu

applied to the inner section of the joint prior to assembly. The gap between the tang and the clevis determines the amount of compression on the O-ring. To minimize the gap and increase the squeeze on the O-ring, shims are inserted between the tang and the outside leg of …

  Engineering, Ring, Ethics, Engineering ethics

HardiePanel Vertical Siding Product Description

www.jameshardiepros.com

end of the wall and snap a straight, level chalk line between the marks as a reference line. That line is for guidance in positioning the top edge of the panels. Check the reference line with a 4 ft. level. 2. Starting on one end and working across the wall, measure and trim the first panel making sure that the edge falls in the middle of a ...

  Check

Related search queries

Check, Proper, Ring, Check for Proper Ring End Gap, Proper ring end gap, End gap, Deere 310 Tractor Loader Backhoe Service Manual, Check for proper, Watts, S-Cam Air Brakes, ENGINEERING ETHICS