2N4401 General Purpose Transistors
2N4401 http://onsemi.com 4 Figure 7. Storage Time IC, COLLECTOR CURRENT (mA) Figure 8. Fall Time IC, COLLECTOR CURRENT (mA) 20 30 50 70 100 10 5.0 7.0 t s, STORAGE ...
Download 2N4401 General Purpose Transistors
Information
Domain:
Source:
Link to this page:
Documents from same domain
Stainless Steel Grade 316 / 1 - Farnell element14
www.farnell.comabc® Aalco is a registered trademark of Aalco Metals Ltd © Copyright: Aalco Metals Ltd, The Hersham Centre, Hersham Green, Hersham, Surrey KT12 4HP All Data is indicative only and must not be seen as a substitute for the full specification from which it is drawn.
SAFETY DATA SHEET COPPER GREASE - Farnell …
www.farnell.comReport Date : 10/10/2013 1 / 7 Revision Date 10/10/2013 Revision 6 Supersedes date 01/08/2011 V5 SDS No. 16238 SAFETY DATA SHEET COPPER GREASE
PRECISION TOOLS - Farnell element14
www.farnell.com10 20 30 40 50 60 70 80 90 100 110 PRECISION TOOLS CATALOGUE www.starrett.com.sg • +65 6365 1088
C60N/H miniature circuit breakers Multi 9 Merlin …
www.farnell.comC60N/H miniature circuit breakers Multi 9 Merlin Gerin The C60N circuit-breaker is a miniature circuit-breaker used for the protection of …
www.weidmueller.com Data sheet
www.farnell.comData sheet Creation date November 22, 2016 12:42:25 PM CET Catalogue status 18.11.2016 / We reserve the right to make technical changes. 1
DOW€CORNING® 732 Multi-Purpose Sealant
www.farnell.comDOW€CORNING® 732 Multi-Purpose Sealant € Product Information TYPICAL PROPERTIES Specifications writers: These values are not intended for use in …
XLP 8-Bit Development Board User's Guide
www.farnell.comXLP 8-BIT DEVELOPMENT BOARD USER’S GUIDE 2011 Microchip Technology Inc. DS41581A-page 3 Table of Contents Chapter 1. Introduction to the XLP 8-Bit Board
Material - Safety - Data Sheet (MSDS) - Farnell …
www.farnell.comNo.5 2/6 3. Composition and Informations on Ingredients Each cell consists of a hermetically sealed metallic container containing a number of chemicals and
Diodes - Farnell element14
www.farnell.comDiodes BA Series Page <2> 20/06/12 V1.1 www.element14.com www.farnell.com www.newark.com Maximum Ratings TA = 25°C unless otherwise specified Type Number Symbol BAW56 / BAV70 / BAV99 Units
Mitutoyo General Catalog - Farnell element14
www.farnell.comMiscellaneous List of products Move to other products SPC Caliper Depth gage H eight gage Micrometer Inside micrometer Micrometer head Indicator Test indicator
Related documents
BMP180 Digital pressure sensor - Adafruit Industries
cdn-shop.adafruit.comTable 1: Operating conditions, output signal and mechanical characteristics Parameter Symbol Condition Min Typ Max Units Operating temperature T A operational -40 +85 °C full accuracy 0 +65 Supply voltage V DD ripple max. 50mVpp 1.8 2.5 3.6 V 1.62 2.5 3.6 Supply current @ 1 sample / sec. 25°C I
LTC6993-6993-1-6993-3-6993-4 (Rev. E)
www.analog.comLTC6993-1/LTC6993-2 LTC6993-3/LTC6993-4 4 e For more information www.analog.com ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. Test conditions are V+ = 2.25V to 5.5V, TRIG = 0V, DIVCODE = 0 to 15 (NDIV = 1 to 221), RSET = 50k to 800k, …
Requirements for Electronic Grade Solder Alloys and Fluxed ...
www.ipc.orgJ-STD-004 Requirements for Soldering Fluxes J-STD-005 Requirements for Soldering Pastes 1.2 Classification Soldering alloys covered by this standard shall be classified by alloy composition and impurity level, solder form and dimensional characteristics peculiar to the solder form, flux percentage and flux classification, if applicable.
2N4401 General Purpose Transistors
www.onsemi.com2N4401 http://onsemi.com 4 Figure 7. Storage Time IC, COLLECTOR CURRENT (mA) Figure 8. Fall Time IC, COLLECTOR CURRENT (mA) 20 30 50 70 100 10 5.0 7.0 t s, STORAGE ...
Surface Mount Multilayer Ceramic Chip Capacitors for ...
www.vishay.comTest Conditions for Capacitance Tolerance: preconditioning for X5R, X7R, Y5V MLCC: perform a heat treatment at +150 °C ± 10 °C for 1 h, then leave in ambient condition for 24 h ± 2 h before measurement Test Conditions for Capacitance and DF Measurement: measured at conditions of 30 % to 70 % related humidity.
Power MOSFET - Vishay Intertechnology
www.vishay.comIRF640, SiHF640 www.vishay.com Vishay Siliconix S15-2667-Rev. C, 16-Nov-15 1 Document Number: 91036 For technical questions, contact: hvm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.