5. External Wall Construction
Concrete surfaces at the joint should be sound, smooth, clean and free from all mortar dust or other contaminants that may affect the adhesion of sealant to the surfaces. Some sealants may require a primer to improve the adhesion. In such cases, manufacturer’s advice should be sought to ensure compatibility of the sealant and primer. As shown
Download 5. External Wall Construction
Information
Domain:
Source:
Link to this page:
Documents from same domain
6. INSTALLATION - Building and Construction …
www.bca.gov.sg25 It is essential to identify location of openings, mechanical and electrical (M&E) services, and other fixtures before installation of drywall.
PUBLIC SECTOR STANDARD CONDITIONS OF …
www.bca.gov.sgContents/3 (Seventh Edition July 2014) 14 Time for Completion 14.1 Contractor to Complete on Time 21 14.2 Extension of the Time for Completion 21
ON TO NEW CHALLENGES - Building and Construction …
www.bca.gov.sgWe shape a safe, high quality, sustainable and friendly built environmentMAY 2017 ON TO NEW CHALLENGES ESCALATING MATTERS BCA GALLERY REOPENS NURTURING GREEN ADVOCATES DR JOHN KEUNG REMINISCES ABOUT HIS TIME AS BCA CEO
6. Common Defects
www.bca.gov.sgand alkyd resins, which are easily affected by light, heat or environmental contaminants • Use non-yellowing paints • Prepare surface and repaint with non-yellowing paints Saponification • Use of alkyd-based paints on cement based materials. …
1. Introduction
www.bca.gov.sg1. Introduction In a survey conducted by BCA in year 2003 involving about 10,000 private residential units, water seepage through external walls was found to be a common defect faced by homeowners. The survey findings also showed that the use of single layer brickwall is the most common cause of water seepage through external walls.
STRATA MANAGEMENT GUIDE : 3
www.bca.gov.sgBuilding Maintenance and Strata Management Act Building Maintenance (Strata Management) Regulations 2005 Managing Agent Management Corporation Strata Title Management Corporation Subsidiary Proprietor AGM BMSMA BM(SM) REGULATIONS MA MCST MC SP Preamble This series of Strata Management Guides published by the Building and …
Solar Photovoltaic (PV) Systems
www.bca.gov.sgpreventive maintenance works, and various incentives to promote solar PV systems in Singapore. We have also refreshed the presentation of the handbook to make it more accessible and reader- friendly, as well as to incorporate examples of completed solar PV installations in …
Design Guide on Use of Structural Steel
www.bca.gov.sgC.1.1 British/European standards on design of steel structures 62 C.1.2 British/European standards on steel materials 62 C.1.3 British/European standards on manufacturing tolerances 63 C.1.4 British/European standards on bolting assemblies 64 C.1.5 British/European standards on welding consumables 65
Issued by the Commissioner of Building Control under ...
www.bca.gov.sgto be used with the adoption of the Eurocodes New Annexes a) Addition of Annex A – Structural design standards based on the Eurocodes and the corresponding Singapore National Annexes. b) Addition of Annex B– Comparative list of Singapore/British standards and their equivalent Singapore/European Standards. 14 Ver 6.0 Section M
Chapter 3 DESIGN CONCEPT FOR PRECAST SYSTEM
www.bca.gov.sgChapter 3 DESIGN CONCEPT FOR PRECAST SYSTEM ... considerations that the formwork cost for construction on grade is negligible, and the extent of in-ground services will, in general, be substantial. ... manufactured separately using materials such as precast concrete, GRC, Aluminium or steel.
Related documents
12 CI/SfB:Yt4 Fosroc Thioflex 600
fosroc.comThe use of a surface primer is always required on porous surfaces. On non-porous surfaces a primer is not normally required except where glass or glazed surfaces are to be permanently immersed in water. Standards compliance British Standard BS 4254:1983. U.S. Federal Specification TT-S-00227E November 1969 (amended 1970). DTp specification for ...
AC-20 +Silicone - Pecora
www.pecora.comsaturation or standing water in porous substrates can be tolerated. Joint Backing: Joints greater than 3/8” (9 mm) should be filled to within 3/8” (9 mm) of the surface with either polyethylene or polyurethane backer rod, preferrably of a non-gassing, non-absorbing type. Use a diameter that will compress about 25% when installed. In joints too
PRODUCT DATA SHEET Sikaflex®-11 FC - Sika Australia
aus.sika.comNon-porous substrates: Aluminium, anodised alumini-um, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles; slightly roughen surface with a fine abrasive pad. Clean and pre-treat using Sika® Aktivator- 205 applied with a clean cloth. Before bonding / sealing, allow a waiting time of > 15 minutes (< 6 hours). Other ...
WHY PRIME? I E Interior/Exterior Limpieza con Agua Hours ...
images.thdstatic.com©2016 Masterchem Industries, 3135 Old Hwy M, Imperial, MO 63052-2834 1-866-PRIMER-1 • www.kilz.com CP-KILZ-FULL-LINE-HD • 50002675 • R1116 KILZ KLEAR ® KILZ 2 ® LATEX KILZ ® PREMIUM KILZ
Vulkem 350/351 - Tremco Sealants
www.tremcosealants.comVulkem Primer #171: A one-part, film-forming primer to be used on porous surfaces. Vulkem 191 Primer – a low-VOC compliant, one-part, porous and interlaminary primer for use in applying a fresh coat of Vulkem coating or sealant after preceding coat …