7. Installation
a) Positioning of sub-frame using ride up blocks or aluminium shin plates b) Checking of plumb and alignment of sub-frame After confirming the setting out of the sub-frame, anchor the sub-frame to the wall. Sub-frame should be temporary stiffened with timber packs near the point of anchoring/ bolting as shown in Figure 7.3. Aluminium shin plate
Download 7. Installation
Information
Domain:
Source:
Link to this page:
Documents from same domain
6. INSTALLATION - Building and Construction …
www.bca.gov.sg25 It is essential to identify location of openings, mechanical and electrical (M&E) services, and other fixtures before installation of drywall.
PUBLIC SECTOR STANDARD CONDITIONS OF …
www.bca.gov.sgContents/3 (Seventh Edition July 2014) 14 Time for Completion 14.1 Contractor to Complete on Time 21 14.2 Extension of the Time for Completion 21
ON TO NEW CHALLENGES - Building and Construction …
www.bca.gov.sgWe shape a safe, high quality, sustainable and friendly built environmentMAY 2017 ON TO NEW CHALLENGES ESCALATING MATTERS BCA GALLERY REOPENS NURTURING GREEN ADVOCATES DR JOHN KEUNG REMINISCES ABOUT HIS TIME AS BCA CEO
6. Common Defects
www.bca.gov.sgand alkyd resins, which are easily affected by light, heat or environmental contaminants • Use non-yellowing paints • Prepare surface and repaint with non-yellowing paints Saponification • Use of alkyd-based paints on cement based materials. …
1. Introduction
www.bca.gov.sg1. Introduction In a survey conducted by BCA in year 2003 involving about 10,000 private residential units, water seepage through external walls was found to be a common defect faced by homeowners. The survey findings also showed that the use of single layer brickwall is the most common cause of water seepage through external walls.
STRATA MANAGEMENT GUIDE : 3
www.bca.gov.sgBuilding Maintenance and Strata Management Act Building Maintenance (Strata Management) Regulations 2005 Managing Agent Management Corporation Strata Title Management Corporation Subsidiary Proprietor AGM BMSMA BM(SM) REGULATIONS MA MCST MC SP Preamble This series of Strata Management Guides published by the Building and …
Solar Photovoltaic (PV) Systems
www.bca.gov.sgpreventive maintenance works, and various incentives to promote solar PV systems in Singapore. We have also refreshed the presentation of the handbook to make it more accessible and reader- friendly, as well as to incorporate examples of completed solar PV installations in …
Design Guide on Use of Structural Steel
www.bca.gov.sgC.1.1 British/European standards on design of steel structures 62 C.1.2 British/European standards on steel materials 62 C.1.3 British/European standards on manufacturing tolerances 63 C.1.4 British/European standards on bolting assemblies 64 C.1.5 British/European standards on welding consumables 65
Issued by the Commissioner of Building Control under ...
www.bca.gov.sgto be used with the adoption of the Eurocodes New Annexes a) Addition of Annex A – Structural design standards based on the Eurocodes and the corresponding Singapore National Annexes. b) Addition of Annex B– Comparative list of Singapore/British standards and their equivalent Singapore/European Standards. 14 Ver 6.0 Section M
Chapter 3 DESIGN CONCEPT FOR PRECAST SYSTEM
www.bca.gov.sgChapter 3 DESIGN CONCEPT FOR PRECAST SYSTEM ... considerations that the formwork cost for construction on grade is negligible, and the extent of in-ground services will, in general, be substantial. ... manufactured separately using materials such as precast concrete, GRC, Aluminium or steel.
Related documents
PRODUCT DATA Aluminium 5052 SHEET UNS A95052 Alloys
www.southernmfg.comconductivity common to all aluminium alloys. It is commonly used in sheet, plate and tube form. Typical Applications Architecture, general sheet metal work, heat exchangers. Chemical Composition Aluminium Development Council of Australia e Key to tempers: Description Aluminium 5052 is an aluminium magnesium alloy which can be hardened by cold
TUBES RECTANGULAR TUBES - Jindal Aluminium
jindalaluminium.com14107 203.20 50.80 3.20 4.279 14057 123.00 24.00 1.06 0.828 14038 127.00 38.10 1.35 1.184 14040 127.00 25.40 1.30 1.052 14078 14079 127.00 38.10 1.74 1.518
IS 737 (2008): Wrought aluminium and aluminium alloy …
law.resource.orgaluminium and aluminium alloy sheet and strip for general engineering purposes. 2 REFERENCES The standards given below contain provisions which through reference in this text, constitute provisions of this standard. At time ofthe publication, the editions indicated were valid. All standards are subject to revision andpartiesto ...
Guide to Nickel Aluminium Bronze for Engineers
www.copper.org6 | GUIDE TO NICKEL ALUMINIUM BRONZE FOR ENGINEERS Broadly, the nickel aluminium bronzes can be classified as alloys containing 6-13% aluminium and up to 7% iron and 7% nickel. The more common alloys normally contain 3-6% each of these two elements. Manganese up to approximately 1.5% is also added, both as a deoxidant and a strengthening element.
The Brazing Guide - GH INDUCTION
www.ghinduction.comOf all the methods available for metal joining, brazing may be the most versatile. Brazed joints have great tensile strength – they are often stronger than the two metals being bonded . together. Brazed joints repel gas and liquid, withstand vibration and shock and are unaf-fected by normal changes in temperature.
National Quali cations 2015
www.sqa.org.ukAluminium 3·95 × 105 Carbon Dioxide ... Attempt ALL questions. Reference may be made to the Data Sheet on Page two of the question paper X757/75/02 and to the Relationship Sheet X757/75/11. Care should be taken to give an appropriate number of significant figures in the final answers to calculations.