A1
A1 BUTT HINGES - Table 2-8A of the National Fire Protection Association (NFPA) handbook No. 80 sets forth the minimum quantity, size and weight (thickness) for swinging fire doors. Table 2-8A also stipulates that “All hinges or pivots, except
Download A1
Information
Domain:
Source:
Link to this page:
Documents from same domain
ALUMINUM GEARED CONTINUOUS HINGES - PBB, …
www.pbbinc.com• For 1-3/4” doors up to 450 lbs. † UL listed for 90 minute rated doors. † Can be UL listed for up to 3 hours. † Flush Mount † For 1-3/4” doors up to 450 lbs.
Full mortise electric hinge template - PBB, Inc.
www.pbbinc.comH (Height) 4.0, 4.5 or 5.0" Full mortise electric hinge template For 4B, 4C, 4F, 4R, BB, CB, FB and RB hinges in sizes shown For SC4B, SC4C, SC4F, SCBB, SCCB and SCFB 4.5 or 5.0" square or beveled hinges
CG31-CG31I-CG31L: CG31PN-CG31P: CG33N-CG33C …
www.pbbinc.comAll PBB Continuous Gear Hinges are offered in standard duty or heavy duty sizes. There are no accessible screws, bolts or pins when the door is closed.
EXPLANATION OF NUMBERING - PBB, Inc. - Hinges
www.pbbinc.comEXPLANATION OF NUMBERING SYSTEMS & SYMBOLS First Two/Four Characters Denotes Style / Function of Hinge: 2B 2H 2P 4B 4C 4F PB BB CP CB CS CH FB IT IF PH RB RS RP SP
Description Page - Hinges
www.pbbinc.comDescription Page General Information A1-A5 Comparison Chart/Finishing Chart A6-A7 Leed Certification A8 Explanation of Numbering System/Product Compliance A9-A10
Template: BB45 - PBB, Inc. - Hinges
www.pbbinc.comPBB, Inc. World Class Hinges 1311 E. Philadelphia Street • Ontario • CA 91761 • USA PBB reserves the right to make changes without notice. 9 Template: BB45
Related documents
Installation Instructions for 45H & 47H Mortise Locks
accesshardware.comInstallation Instructions for 45H & 47H Mortise Locks BEST ACCESS SYSTEMS a Division of Stanley Se curity Solutions, Inc. 5 Installing the trim 9 Install trim mounting plates 1 For J trim, position the J alignment plate (Figure 11b) on the outside of the door.
Security Mortise Locks - Baldwin Hardware Online
www.baldwinbrassdepot.com©2005 BALDWIN HARDWARE CORPORATION, READING, PA 19611 h 2 REVISION APR 2005 Mortise Locks—Specifications Most working parts are manufactured of solid forged brass material, precisely machined for
Mortise Locksets ML2000 Series - corbin-russwin-hardware.com
www.corbin-russwin-hardware.comML2000.7 ML2000 Series Mortise Locksets Functions Series/ ANSI No. Outside Inside Function Type Series 1000 Function Description - Latchbolt by grip either side. - Deadbolt by key outside or by thumbturn lever inside.
#AMDB3 Adjustable Mortise Door Bottom - dhsi-seal.com
www.dhsi-seal.comAdjustable Mortise Door Bottom Installs in bottom of hollow metal door using AMDB3 Conversion Channel #AMDB3-CC Designed with unique features: Twist-Lok conical springs
ML-1100 SERIES MORTISE LOCK & PULL - DORTRONICS
www.dortronics.comML-1100 SERIES MORTISE LOCK & PULL Clean Architectural Appearance 1000 Pounds of Holding Force Tamper-proof Mounting Totally Concealed Lock & Armature
676 Petrolia Road Installation Instructions Electric ...
www.lawrencehardware.comLH/LHR RH/RHR Rotate 180 Deg. Handing Screw Handing Instructions for Mortise Locks Template for ML170/180/182/1480/1485 Mortise Locks STEP 1: Locate the handing screw.This screw is …
Mortise Exit Device Installation Guide - TownSteel Inc
www.townsteel.comFor Single Door For Double Door CL CL 3 CL CL CL RHR Cut-out for All 1300 Series Mortise Exit Device RHR shown (LHR opposite) STRIKE PREPARATION *PREPARE HOLES AFTER
Mortise locks - Valli&Valli
www.vallievalli.com184 Mortise locks Lever and Knob sets with rosette trim (specify RT, RP, RQ, RS) FIG.11 and 12. Lever and Knob sets with long escutcheon trim (specify ET, EP, ER, NES) For figures refer on page 138/139.