Basic concepts for explosion protection - BARTEC
an Explosion Protection Document is a precondition for setting up and operating a potentially explosive facility. Only such a document makes it possible to select protective systems and equipment with respect to explosion protection and to install, operate, maintain and eventually repair them in compliance with standards. The corresponding
Download Basic concepts for explosion protection - BARTEC
Information
Domain:
Source:
Link to this page:
Documents from same domain
II 2G Ex db eb IIC T6 Gb X - BARTEC
www.bartec.deMarking according directive 2014/34/EU according norm EN 60079-0 Marking of electrical equipment for use in potentially explosive atmospheres BARTEC GmbH Max-Eyth-Str ...
Marking of non-electrical explosion protected equipment ...
www.bartec.decarbon dust operation where there is a risk of explosion - I M1 I Ma disconnection where there is a risk of explosion - I M2 or M1 I Mb or Ma Gas groups IIA IIB IIC Permitted Equipment groups IIA, IIB, IIC IIB, IIC IIC ATEX Gases/Vapours NB1) II 1G Ex h IIC T6 Ga NB2) 18 ATEX 1234 X Dusts II 2D Ex h IIIC T120 °C Db X ISO (IECEx)
Marking of NEC electrical explosion protected equipment
www.bartec.demotors, fuses, switchgear, power electronics Gases, vapors Propagation of an explosion inside to the outside is excluded Flameproof Explosionproof UL 1203 (Div. 1+2) FM 3615 ANSI/UL-60079-1 Ex da Ex db Ex dc Junction and connection boxes, enclosures, motors, lights, terminals Gases, vapors Avoidance of arcs, sparks and excessive temperature
ELECTRIC MOTORS - BARTEC
www.bartec.deThese are the three-phase, asynchronous electric motors with short-circuit rotor, explosion protected according to the CENELEC EN 60079-0, EN 60079-1, EN 60079-7 (IEC 60079-0, IEC 60079-1) standards. The enclosures of electric motors are designed to be “flameproof“ according to EN 60079-0 (IEC 60079-1).
ComEx Actuating elements - BARTEC
www.bartec.de– DIN EN 60204-1: 2007 – DIN EN 60947-5-1: 2005 (VDE 0660 Teil 200) Pushbutton with imprint “NOT-AUS EMERGENCY STOP” “Pull to Release” 05-0003-000800 Pushbutton with imprint “ARRET” 05-0003-000802 Pushbutton yellow, unlabelled 05-0003-000801 Pushbutton black, unlabelled 05-0003-000803 Pushbutton red, unlabelled 05-0003-000804
ComEx Control Stations - BARTEC
www.bartec.deE Switching or illuminating module or terminal block FF 00 – without accessory 01 – protective metal shroud 02 – external earth connection 03 – shroud + external earth connection 10 – labelling by template 18 – locking device 33 – earth plate 99 – on request Selection Key ComEx Control Station 0 7 - 3 5 * A E * - * * * B C D * D ...
Kennzeichnung elektrischer explosionsgeschützter Geräte ...
www.bartec.deKennzeichnung elektrischer explosionsgeschützter Geräte (ATEX/IECEx) - bedeutet: NICHT möglich anzuwenden. + bedeutet: Anwendung möglich. 1) Kennnummer der notifizierten Stelle (Notified Body) zuständig für die Zertifizierung des Hersteller- Qualitätssystems (Kat. 1 und 2).
Marking of electrical explosion protected equipment …
www.bartec.deIECEx Gases/Vapours Ex db eb IIB T4 Gb IECEx ExCB3) 11.1234 X Dusts Ex tc IIIB T120 °C Dc IECEx ExCB3) 11.1234 X Subdivisions and classification of gases and vapours Gases and vapours Assignment of gases and vapours accordance to the ignition temperature Temperature class Maximum surface temperature (equipment) Permitted Temperature classes ...
Related documents
Explosion Venting Systems
cms.esi.infoExplosion Protection by Deflagration Venting’ • Explovent ® meets the guidelines of FM 1-44 and includes FM tested and approved models, which are listed on the online FM APPROVAL GUIDE www.approvalguide.com EXPLOVENT WALL VENTING PANELS The only venting system that can be tested at any time to ensure that panels are functioning as intended
Class/Division Hazardous Location - Rockwell Automation
literature.rockwellautomation.comClass/Division Hazardous Location 33 Introduction A major safety concern in industrial plants is the occurrence of fires and explosions. No other aspect of industrial safety receives more attention in the form of codes, standards, technical papers, and engineering design.
Marking of non-electrical explosion protected equipment ...
www.bartec.deProtection by flow restricting enclosure – – fr EN 13463-2 Mill, geared motor, complex assembly group Dusts (D) This protection principle prevents the hazardous atmosphere reaching the source of ignition. Protection by enclosure Ex h Ex ta Ex h Ex tb Ex h Ex tc EN ISO 80079-36 EN IEC 60079-31 Brakes Gases and vapours (G) This protection ...
Fire, Explosion and Risk Assessment Topic Guidance
www.hse.gov.uk1 Introduction This document provides guidance for assessors of Safety Cases on the topic of fire, explosion and risk assessment. It serves as a supporting reference to the Safety Case Handling and Assessment Manual (SCHAM). The overall objective of this guidance is to promote greater consistency and effectiveness in
Safe collection of wood waste: Prevention of fire and ...
www.hse.gov.ukwaste through an explosion choke, eg a rotary valve, or directly into strong metal containers clamped firmly to the discharge outlets. Where rotary valves are intended to act as explosion chokes, they must be certified as explosion protection devices under the Equipment and Protective Systems Intended for Use in Explosive Atmospheres
Overview of Explosion Protection Techniques
www.iecex.comOverview of Explosion Protection Techniques IECEx 2018 International Conference Jakarta, Indonesia 8 thand 9 August 2018
ARTICLE HAZARDOUS (CLASSIFIED) LOCATIONS
www.mikeholt.comA hazardous (classified) location is an area where the possibility of fire or explosion can be created by the presence of flam-mable or combustible gases or vapors, combustible dusts, or easily ignitable fibers/flyings. Electric arcs, sparks, and/or heated surfaces can serve as a source of ignition in such environments.