Bridge Design Guide - ftp.txdot.gov
the back of the barrier and the edge of the slab is less than 2 feet, pin the barrier to the deck. If possible, allow a 2 ft. buffer when placing the temporary barrier on new bridge ... Chapter 3 — Superstructure Design Guidelines Section 2 — Superstructure Phasing Guidance Bridge Design Guide 3-9 TxDOT January 2020
Download Bridge Design Guide - ftp.txdot.gov
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Advertisement
Documents from same domain
CONSTRUCTION INSPECTION REPORT
ftp.txdot.govIn addition to on-site Other Entity (OE) inspection review, TxDOT will verify OE inspection documentation is adequate during the course of construction. Note that not all activities listed below will be applicable on every project; therefore, inspection review is only necessary for the applicable
Report, Construction, Inspection, Construction inspection report
THIS PAGE LEFT BLANK - Texas Department of Transportation
ftp.txdot.govCompliant Work Zone Traffic Control Devices A. Introduction TxDOT A-1 December 2017. A. INTRODUCTION. This list contains products that have been evaluated and determined to be acceptable traffic control devices
Control, Blanks, This, Pages, Left, Traffic, Work, Zones, Traffic control, Work zone traffic control, This page left blank
DMS - 6310 JOINT SEALANTS AND FILLERS
ftp.txdot.govDEPARTMENTAL MATERIALS SPECIFICATION JOINT SEALANTS AND FILLERS TEXAS DEPARTMENT OF TRANSPORTATION 1 – 6 04/09–05/10 DMS - 6310 JOINT SEALANTS AND FILLERS EFFECTIVE DATES: APRIL 2009–MAY 2010. 6310.1. Description. This Specification establishes the requirements for the various types of joint sealants, backing materials, and joint fillers …
Joint, Sealant, 1306, Fillers, Joint sealant, Joint filler, Joint sealants and fillers, Dms 6310 joint sealants and fillers
1993 SPECIFICATIONS CSJ 0218-04-075 SPECIAL …
ftp.txdot.gov1993 SPECIFICATIONS CSJ 0218-04-075 SPECIAL SPECIFICATION ITEM 3148 WIDE FLANGE PAVEMENT EXPANSION JOINT 1. Description. This Item shall govern for the construction of wide ... Item 433, "Joint Sealants and Fillers" Item 440, "Reinforcing Steel" Item 442, "Metal For Structures"
Specification, 2018, Special, Joint, Expansion, Pavement, Sealant, Flange, Wide, Fillers, Joint sealants and fillers, 0218 04 075 special, 0218 04 075 special specification, Wide flange pavement expansion joint
ITEM 420 CONCRETE STRUCTURES
ftp.txdot.gov433, "Joint Sealants and Fillers". (a) Preformed Fiber Material. Preformed fiber expansion joint material shall conform to the dimensions shown on the plans. Unless otherwise specified, "Preformed Bituminous Fiber Material" shall be used. (b) Joint Sealing Material.
ITEM 360 CONCRETE PAVEMENT - ftp.txdot.gov
ftp.txdot.govUnless otherwise shown on the plans, the joint sealant materials to be used shall conform to the requirements of Class 5 joint sealant as described in Item 433, "Joint Sealants and Fillers". (3) Dowels for Expansion and Contraction Joints.
Special Specification 6007 Intelligent Transportation ...
ftp.txdot.govconnectors, moisture or water sealants, terminators, splice trays, fiber optic jumpers, pig tails, fiber patch panels, fiber interconnect housing, and accessories necessary to complete the fiber optic …
Specification, Brief, Special, Intelligent, Topics, Transportation, 7600, Fiber optic, The fiber optic, Special specification 6007 intelligent transportation
Item 420 Concrete Substructures - ftp.txdot.gov
ftp.txdot.gov420 2 Manila hemp may also be used to make burlap. Do not use burlap fabricated from bags. Do not use burlap containing any water soluble ingredient which will retard the setting time of concrete.
2014 Standard Specifications for Construction and ...
ftp.txdot.govStandard Specifications for Construction and Maintenance of Highways, Streets, and Bridges Adopted by the Texas Department of Transportation November 1, 2014
Standard Specifications for Construction and Maintenance ...
ftp.txdot.govEach specification is outlined by Articles and Sections. The basic Articles required for a specification are: 1. DESCRIPTION 2. MATERIALS 3. EQUIPMENT 4. CONSTRUCTION OR WORK METHODS 5. MEASUREMENT 6. PAYMENT Some Articles are not used in every Item. Measurement and Payment Articles are combined when the work described is
Related documents
Pipeline Separation Design & Installation Guidance
apps.ecology.wa.govPipeline separation provides the final barrier of protection in the multi-barrier approach to pipeline protection. Other barriers include: 1) the selection of the pipe material, 2) pipe ... Provide general design guidance regarding approaches that can be approved by the regulatory agencies and can be applied without case-by-case, individual ...
Design, Guidance, Barriers, Separation, Design guidance, Separation design
Temporary Traffic Control Design Guidelines
azdot.govtraffic control devices, this design guide is intended to provide additional guidance to designers, field construction and maintenance personnel, and contractors in establishing and implementing safe, efficient, well‐conceived traffic control plans. This design guide should be used as an extension of the
Guidelines, Design, Control, Guidance, Traffic, Temporary, Temporary traffic control design guidelines
TRAFFIC SAFETY SYSTEMS GUIDANCE - Caltrans
dot.ca.gov4.6 Barrier Design Details 53 06-01-2017 4.7 Median Design Considerations 54 06-01-2017 4.8 CHP Enforcement Areas / Emergency Passage-ways 59 06-01-2017 4.9 Glare Screens 59 06-01-2017 4.10 Delineation 60 06-01-2017 5 OUTER SEPARATION BARRIER …
Checklist for Existing Facilities version 2 - ADA
www.ada.govDesign (Standards). The ADA Accessibility Guidelines (ADAAG), when adopted by DOJ, became the Standards. The Standards are part of the Department of Justice Title III Regulations, 28 CFR Part 36 (Nondiscrimination on the basis of disability… Final Rule). Section 36.304 of this regu-lation, which covers barrier removal, should be
Guidance on Barrier Design - Building Performance
www.building.govt.nzGUIDANCE ON BARRIER DESIGN – MARCH 2012 6 2.0 Guidance and the Building Code The aim of this document is to provide guidance on how the relevant Building Code performance criteria can be achieved for barriers. Barriers are required to meet the performance criteria described in the Building Code. The relevant Building Code clauses for barriers ...
HIGHWAY DESIGN MANUAL Chapter 10 Roadside Design, …
www.dot.ny.govThe guidance for performing an accident analysis will be found in Chapter 5 - Basic Design. The guidance for making upgrade judgments is presented under Section 10.3, Existing Facilities. Additional guidance for work on existing facilities is presented in Chapter 7 - Resurfacing, Restoration, and Rehabilitation (1R, 2R & 3R).
Hygienic Design of Food Manufacturing Premises
www.ifst.orgSite barrier (1) Non -food production areas ... High hygiene area M icrobiologically decontaminated products, design risk assessed Aseptic barrier (4) ² may be medium or high hygiene Zoning and barriers . Site Soil/dust/water Air Air Air ... National guidance e.g. Defending food and drink PAS 96:2008 British Standards . G ...