Catalog 457377 2014
Use a qualified, calibrated torque wrench. Do not use an impact gun to install the axle nut. The impact gun will damage the axle nut. It will also leave your spindle nut under or over torque resulting in hub assembly failure. To ensure that you have the correct torque for the application refer to this guide or contact the vehicle manufactures ...
Download Catalog 457377 2014
Information
Domain:
Source:
Link to this page:
Documents from same domain
SKF Torque specification guide - caissiedrive.net
caissiedrive.netCatalog 457377 2011 Supercedes 457377, Dated 2010 Torque specification guide Front & rear axle nut torque specifications for FWD, RWD & 4 W/D vehicles
Symptoms of a Worn Wheel Hub Bearing - …
caissiedrive.netJune Tech Tip Hudson 800-696-7004 Worcester Symptoms of a Worn Wheel Hub Bearing • Snapping, clicking or popping. • Grinding when the vehicle is in motion.
SKF Torque specification guide - PHP Hosting
caissiedrive.netOne of the most common mistakes during installation is improper torque of the Axle nut. To guarantee the (Bearing, Spindle or Hub) is torqued correctly, follow the manufacture’s installation procedure. Ignoring these important details will reduce the life of your (Bearing, Spindle or Hub). Use a qualified, calibrated torque wrench.
Related documents
PreSet Hub - ConMet
conmet.comTorque Specifications Item Measurement Torque (ft-lbs) Notes Ball Seat Wheel Nut 3/4 - 16 1 1/8 - 16 450 - 500 Always tighten the top nut first or pilot damage may result. Do not lubricate the faces of the hub, drum, wheel or on the ball seats of the wheel nuts. The last nut rotation should be with a calibrated torque device. Hub Pilot Wheel Nut
T5C Parts Manual Sec 1 - aepsurplus.com
www.aepsurplus.comOil Change and Type Specifications When your machine is new, the hydraulic system oil and filter must be changed within the first 50 hours of use and every 250 thereafter. Refill the hydraulic reservoir with engine oil type API SF.CD 15W40 when outside temperature is above 40 degrees F. Use engine oil type API SF.CD 10 weight
Service Manual - Dana Incorporated
www.dana.com8 - Hex Nut, Spindle 9 - Cotter Pin 10 - Steering Knuckle 11 - Cotter Pin 12 - Hex Nut, Steer Arm 13 - Seal Knuckle 14 - Shim 15 - Thrust Bearing 16 - Draw Key 17 - Nut, Draw Key 18 - Stop Screw 19 - Nut, Jam ... EFA Family Fastener Torque Specifications nut. specifications.)
FASTENER IDENTIFICATION AND TORQUE DATA
www.inetefb.comThe amount of torque required to run the nut down (friction drag torque) should be measured and added to the amount of torque specified for the fastener. ... spindle nut 32-20 (Refer to 32-20) (Refer to 32-20) (Refer to 32-20) (Refer to 32-20) ... Torque Specifications for High Strength Steel Tension Nuts and Bolts with FINE Threads Item Thread ...
Installation Procedure and Wheel Bearing Adjustment ...
www.stemco.comThread the nut onto the axle until hand tight against the bearing. STEP 2 SEAT THE BEARING: With hub or hub/drum only: Using a torque wrench: A (1) Tighten the nut to 200 ft-lbs. Spin the wheel at least one full rotation. (2)Tighten the nut to 200 ft-lbs. Spin the wheel at least one full rotation. (3)Tighten the nut to 200 ft-lbs.