CHROMABASE BASECOAT - Axalta

LE MULTI-PANEL CLEARCOAT - axalta.com

Page 1 of 4 CROMAX® LE LE5100S™ MULTI-PANEL CLEARCOAT GENERAL DESCRIPTION A VOC compliant, two-component clearcoat designed for panel and multi-panel repairs in air dry and low bake …

  Beka

Corlar® 2.1 ST™ Satin High Solids Epoxy Mastic

Corlar 2.1 ST may also be used as a high performance tank lining primer on carbon steel or concrete for immersion service in near neutral pH water, fresh water, or saltwater. Corlar 2.1 ST is not recommended for use with potable water. Contact your Axalta representative for specific immersion service recommendations and procedures.

  Performance, High, High performance

SelectSeal 0™ / 1™ / 422-52™ 2K Urethane Sealer - Axalta

Clean spray equipment as soon as possible with lacquer thinner or low VOC cleaner in VOC regulated markets. IMPORTANT NOTES 422-5X™ can be used under any Nason® topcoat If sealer dries overnight, scuff and recoat Do NOT apply directly over areas of bare metal DRY TIMES Allow at least 15 minutes flash time before applying topcoats.

  Thinner, Lacquer, Lacquer thinner

CHROMASYSTEM™ MIDCOAT BASE 11000S™

VOC REGULATED AREAS These directions refer to the use of products which may be restricted or require special mixing instructions in VOC regulated areas. Follow mixing usage and recommendations in the VOC Compliant Products Chart for your area. SAFETY AND HANDLING For industrial use only by professional, trained painters.

Ful-Poxy 491-16 DTM Epoxy Primer/Sealer - Axalta

Properly sanded or blasted steel Properly cleaned or sanded aluminum, galvanized steel, or stainless steel Properly sanded SMC/fiberglass/body fillers/polyester putties TOPCOATS Any refinishing systems SURFACE PREPARATION Prior to sanding, remove all wax, grease, oil, and road tar with Nason® 441-05™

  Steel, Resale, Primer, Epoxy, Galvanized, Galvanized steel, Dtm epoxy primer sealer

Ful-Thane 2K Urethane Binder (IB Quality)

Technical data sheet SAFETY AND HANDLING For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and SDS/MSDS precautions. If mixed with other components, mixture will have hazards of …

  Sheet, Data, Safety, Safety data sheet

2030 Sustainability Goals - axalta.com

2030 Sustainability Goals 80% of new technology and innovation developments will have a sustainability benefit 100% active global employees trained on Code of Business Conduct and Ethics 10% reduction of process waste, VOC emissions, and water use from operations (normalized to production) 50% absolute reduction of Scope 1

  2003

CHROMASYSTEM™ MIDCOAT …

ChromaPremier® Basecoat ChromaBase® Basecoat 222S™ Midcoat Adhesion Promoter Cromax® Pro Basecoat Cromax® Mosaic™ Cromax® EZ GUN SETUPS* HVLP: 1.3 mm-1.4 mm Compliant: 1.2 mm-1.3 mm . Page 2 of 4 AIR PRESSURE* HVLP: 8-9 psi at cap Compliant: 25-30 psi * Refer to the manufacturer’s directions for gun specific recommendations ...

  Basecoat

Ful-Base Basecoat (IF Quality) - Axalta

OEM basecoat/clearcoat finishes. The products referenced herein may not be sold in your market. Please consult your distributor for product availability. MIXING COMPONENTS Ful-Base® Basecoat IF Quality Ful-Base® 430-XX Tints Ful-Base® 435-93™ Basecoat Binder Ful-Base® 483-30™ Basecoat Activator Ful-Base® 441-2X™ Reducers *Do not use ...

  Basecoat

Ful-Cryl II 2K Acrylic Enamel Topcoat (ID Quality) - Axalta

POT LIFE 4 hours at 70°F (21°C) SPRAY VISCOSITY 20-21 seconds in a Zahn #2 ADDITIVES Fisheyes Add 2-4 oz (60-120 ml) Nason® 495-01™ Fisheye Eliminator per RTS gallon, as needed. APPLICATION SUBSTRATES All OEM finishes, as well as properly prepared metal, fiberglass, plastic and fully cured previously painted surfaces. SURFACE PREPARATION