Classification societies – what, why and how?

IACS UR’s and Panel Responsible

IACS UR’s and Panel Responsible Page 2 of 13 UR Ex (Electrical and Electronic Installations) UR Title Panel Responsible E1 Revised see M3.2

  Responsible, Panels, Ur s and panel responsible

Interpretations of the International Convention for …

INTERNATIONAL ASSOCIATION OF CLASSIFICATION SOCIETIES Interpretations of the International Convention for the Safety of …

  International, Interpretation, Convention, Interpretations of the international convention

Record of Approved Ship Safety Equipment - IACS

No.128 Class Register No.: _____ Page 1 of 30 Page 1 of 30 IACS Rec. 2015. No. 128 (cont) Record of approved Ship Safety Equipment(Nov. To meet the provisions of the

  Safety, Ship, Approved, Equipment, Of approved ship safety equipment

AUGUST, 2016 Joint Safety Statement on Safety of …

Joint Safety Statement on Safety of Surveyors AUGUST, 2016 This document is further supported by the IACS Occupational Safety and Health (OSH) Policy.

  Safety, Testament, Joint, Surveyor, Joint safety statement on safety of, Joint safety statement on safety of surveyors

Requirements concerning LOAD LINE - IACS

L5 Page 2 of 9 IACS Req. 2004/Rev.2 2006 L5 (cont’d) - The onboard computer software for stability calculations is ship specific and the results of the calculations are only applicable to …

No.47 Shipbuilding and Repair Quality Standard - IACS

- 5 - Imperfection surface area Ratio (%) is obtained as influenced area / area under consideration (i.e. plate surface area) x 100%. For isolated surface discontinuities, influenced area is obtained by drawing a continuous line which follows the

  Standards, Quality, Repair, Shipbuilding, 47 shipbuilding and repair quality standard

No.17 Reporting by Surveyors of Deficiencies relating to ...

, a part of the ship’s structure or its machinery, equipment, fittings, or a failure in the documentation, possibly arising from the lack of implementation of the ISM Code on board.

  Implementation

No.31 Inclining test unified procedure - IACS

No. 31 Inclining test unified procedure 1. Introduction The purpose of this procedure is to achieve a satisfactory accuracy in the determination of the lightship

  Tests, Procedures, Unified, Inclining test unified procedure, Inclining

LNG BUNKERING GUIDELINES - IACS

LNG bunkering is the process of transferring LNG fuel to a ship from a bunkering facility. ... •Selection of equipment, Training, Check List •Chapter 3 Section 1 . Pre bunkering phase •Preparation for safe bunkering •Chapter 3 Section 1. Connection •Inerting, coupling and testing

  Lists, Check, Check list, Bunkering

No.47 Shipbuilding and Repair Quality Standard

1.1 This standard provides guidance on shipbuilding quality standards for the hull structure during new construction and the remedial standard where the quality standard is not met. Whereas the standard generally applies to - conventional merchant ship types, - parts of hull covered by the rules of the Classification Society,

  Repair, Ship, Shipbuilding

THE NATIONAL SHIPBUILDING RESEARCH PROGRAM

ship production committee facilities and environmental effects surface preparation and coatings design/production integration human resource innovation

  Ship

Glossary of “Class“ related terms, abbreviations and …

www.amem.at continuous improvement. Certification is based on the adherence to international statutory rules. A formal document attesting compliance of a

  Rules

The rules and regulations applicable to yachts over …

AFS International Convention on the Control of Harmful Anti-Fouling Systems on Ships, 2001 SUMMARY OF REQUIREMENTS Minimising the harmful effects of anti-fouling

  Rules, Regulations, Over, Applicable, Yacht, The rules and regulations applicable to yachts over

AGUIDEFORINTERPRETATION OF …

ssc-245 aguideforinterpretation of nondestructivetests ofordinary-, medium-,andhigh-strengthlow-alloy steel butt-jointweldments inship hullstructures

  Medium, Aguideforinterpretation of, Aguideforinterpretation, Aguideforinterpretation of nondestructivetests ofordinary, Nondestructivetests, Ofordinary

SPECIFICATION FOR 40.37 METRE 70 PAX - Sun …

40.37m CREW BOAT TECHNICAL SPECIFICATION DESIGN REF# S750-110_P DATE 30 /10 2013 Re vision Number: 1 Page 2 of 20 1.0 Design The vessel will be designed to comply with the chosen classification society crewboat rules and OSV code for statutory matters.

  Rules, Specification, Classification, Meters, Specification for 40, 37 metre 70

Class notation Description TL T-M T[M]

Class notation Description BULK CARRIER Additional class notation assigned to the ships designed for carriage of solid bulk cargoes and comply with TL Rules…

  Rules, Descriptions, Class, Notation, Class notation description