COLD-FORMED STRUCTURAL FRAMING PRODUCTS technical …
stronger . than steel. sm. cold-formed structural framing products . technical design guide. member properties & spans • curtain walls • load-bearing walls • joists • framing details
Download COLD-FORMED STRUCTURAL FRAMING PRODUCTS technical …
Information
Domain:
Source:
Link to this page:
Documents from same domain
METAL LATH & ACCESSORIES for stucco & stone
www.clarkdietrich.comOverview and General Notes Application Standards Trademarks and Warranty ... The list of our lathing products goes on, but there is much more to us than that. We refer to ourselves as ClarkDietrich for a reason. When you specify or choose our product line, you get fully ... Twin Trac No. 17 wire, 1-1/2" x 1-1/2" 2.5# dia. / Steel Stud/Sheathing ...
For Best Non-Structural Steel Stud Specifications, Stay ...
www.clarkdietrich.comadvantage of new, higher-strength steels available today, as well as new steel processing methods. They may have also added more steel into the strip width used to make the studs. Reinforcing ribs and other reinforcing devices have been added to the flanges and/or webs. NON-STRUCTURAL STEEL STUD SPECIFICATIONS | 7 clarkdietrich.com
Best Practices for Selection and Installation of Expanded ...
www.clarkdietrich.comto the framing members, improper installation of paper-backed lath, incorrect fastening of the adjoining sheets at the laps and the improper orientation of the lath sheets. A well-defined installation primer for laths with or without paper can be found in ASTM C1063, or the Expanded Metal Lath Association’s Guide Specifications for Metal Lathing
AN INTRODUCTION TO COLD-FORMED STEEL FRAMING
www.clarkdietrich.comCorrosion Resistance • Steel framing members built into wall cavities, attic ... • Over $1 billion is spent annually for prevention and control of termites, and to address the damage they create. ... concrete and other types of construction materials.
ximum Spans - ClarkDietrich
www.clarkdietrich.comThe minimum available TradeReady® rim track thickness is used. 3.) Recommended bridging is 8'0" on center maximum. 4.) Fy is 33 ksi for 18 gauge, 50 ksi for 16,14, and 12 gauge. 5.) If an additional point load is located @ the end bearings (e.g. from a wall above), w eb crippling must be checked separately. 6.) The minimum bearing stud flange ...
ProSTUD Composite Limiting Heights 5/8 Type X Gypsum Board
www.clarkdietrich.comComplies with AISI S100-16 AISI S220-15 IBC 2018 COMPOSITE—5/8" TYPE X ProSTUD ® Composite Limiting Heights Notes: – Allowable composite limiting heights were determined in accordance with ICC-ES AC86-2019. – Additional composite wall testing and analysis requirements of the SFIA Code Compliance Certification Program were observed.
AREA SEPARATION WALL SYSTEMS - ClarkDietrich
www.clarkdietrich.comINSTALLATION PROCEDURES Clips melt away under intense heat. ... to replace the design, drawings, specifications, and decisions of a professional architect or engineer. ... WEST Carlsbad, CA ClarkDietrich Building Systems is a proud member of the Steel Framing Industry Association (SFIA).
COLD-FORMED STRUCTURAL FRAMING PRODUCTS technical …
www.clarkdietrich.comClarkDietrich Engineering Services is licensed throughout the United States and can be reached by calling 877-832-3206. ClarkDietrich Technical Services —For general technical service on products, member sizing, industry standards, framing details or information on engineering software, please call technical services at 888-437-3244.
ClarkDietrich PRODUCT INFORMATION Example: 362S162-43 ...
www.clarkdietrich.comIron and Steel Institute (AISI) for identifying each of its products. Coding of each member consists of four parts, in this order: • A number which identifies the web depth of the member to two decimal places. 600 = 6.00," 1000 = 10.00," 550 = 5.50," 362 = 3.625," etc. • A letter that tells you the type of member, such as
Related documents
SPACE STANDARDS, GUIDELINES, AND PROCEDURES
www.osec.doc.gov01. This document establishes the standards, guidelines and procedures for the management of space within the Herbert C. Hoover Building (HCHB), and serves to
EXAMPLE 1: THREE-SPAN CONTINUOUS STRAIGHT …
connect.ncdot.govEXAMPLE 1: THREE-SPAN CONTINUOUS STRAIGHT COMPOSITE I GIRDER Load and Resistance Factor Design (Third Edition -- Customary U.S. Units) by Michael A. Grubb, P.E.