COMMAND - Benjamin Moore & Co.
Jul 22, 2020 · Emulsifier V600 or solvent wiping in accordance with SSPC-SP1 prior to coating. Prime properly prepared surfaces with Acrylic Metal Primer V110, Waterborne Bonding Primer V175 or apply 1-2 coats of COMMAND™ direct. Wood Surfaces: For best results, prime bare spots and new wood with a quality acrylic primer.
Download COMMAND - Benjamin Moore & Co.
Information
Domain:
Source:
Link to this page:
Documents from same domain
BRIGHTEN RESTORE REMOVE a b c Weathered …
media.benjaminmoore.com48 48 REFINISH DECKS WITH ARBORCOAT® Treat the wood.Determine the wood you have to treat most appropriately. Check the weather. …
solid stain colors semi solid stain ... - Benjamin …
media.benjaminmoore.comsolid stain colors semi solid stain colors PLEASE NOTE: These representations of stained substrates can only approximate the actual color and opacity.
ADVANCE - Benjamin Moore & Co.
media.benjaminmoore.comOct 12, 2018 · Qualifies for LEED® v4 Credit Qualifies for CHPS low emitting credit (Collaborative for High Performance Schools) CDPH v1 Emission Certified Class A (0-25) over non-combustible surfaces when tested in accordance with ASTM E-84 Water Vapor Transmission: ASTM D1653 (method A): 2.55 perms
ALIPHATIC ACRYLIC URETHANE GLOSS V500
media.benjaminmoore.comJul 23, 2018 · Aliphatic Acrylic Urethane is a multi-use, two-component urethane appropriate for use on both metal and masonry. This product provides excellent gloss and color retention when used on exterior surfaces exposed to sunlight and rain, and the highly cross-linked formula provides superior abrasion, chemical, and solvent resistance.
WATERBORNE AMINE EPOXY V440
media.benjaminmoore.comJul 25, 2018 · Benjamin Moore & Co., 101 Paragon Drive, Montvale, NJ 07645 Tel: 866-708-9180 Fax: 888-248-2143 www.benjaminmoore.com M72 …
POLYAMIDE EPOXY COATING GLOSS/SEMI-GLOSS V400
media.benjaminmoore.comAug 03, 2018 · Benjamin Moore & Co., 101 Paragon Drive, Montvale, NJ 07645 Tel: 866-708-9180 Fax: 888-248-2143 www.benjaminmoore.com M72 …
STIX - Benjamin Moore & Co.
media.benjaminmoore.comSep 09, 2019 · Technical Data White Vehicle Type Urethane Modified Acrylic Pigment Type Titanium Dioxide Volume Solids 40.0 ± 1.0% Coverage per Gallon at Recommended Film Thickness 300 – 400 Sq. Ft. Recommended Film Thickness –Wet 4.0 - 5.5 mils –Dry 1.6 - 2.2 mils Depending on surface texture and porosity. Be sure to estimate the
ADVANCE - Benjamin Moore & Co.
media.benjaminmoore.comOct 12, 2018 · • Easy application • Easy clean up • Block resistant ... Cured plaster should be hard, have a slight sheen and maximum pH of 10; soft, porous or powdery plaster indicates improper cure. Never sand a plaster ... Refer to Safety Data Sheet for additional health and safety information.
V110 - Benjamin Moore & Co.
media.benjaminmoore.comJul 24, 2018 · V200 Line, V201, V230 Line, V231 Line, V220 Line, V300 Line, V520 Line, 540 Line, and Other Acrylics, Vinyl Acrylics & Alkyds V110 Waterborne DTM Metal Primer can be used as a barrier coat on top of older coatings prior to application of high performance coatings with “hotter” solvents, such as 2 component epoxies and urethanes.
STIX - Benjamin Moore & Co.
media.benjaminmoore.comSep 09, 2019 · Surface wax should be removed with a commercial wax stripper. Grease residue should be removed with a grease and oil emulsifier. Remove all loose chipping, cracking and peeling from previously painted surfaces by hand scraping, sanding, wire brushing and/or by use of power tool cleaning methods such as electric sanders,
Related documents
Interzinc - AkzoNobel
international.brand.akzonobel.comNov 23, 2016 · with SSPC-SP1 solvent cleaning. Abrasive Blast Cleaning Abrasive blast clean to a minimum of SSPC-SP6 or Sa2½ (ISO 8501-1:2007), (or SSPC-SP10 for optimum performance). If oxidation has occurred between blasting and application of Interzinc 22, the surface should be reblasted to the specified visual standard.
SURFACE PREPARATION AND PAINTING STRUCTURAL STEEL …
dot.state.mn.usan appropriate cleaning solution. All visible traces of contaminants are to be removed with final wiping performed with clean rags and clean solvent. A discussion of solvent cleaning methods and Specification SSPC-SP1-"Solvent Cleaning" are included in Figure 5-393.456 (12) thru (13). Surfaces of steel members for which blast cleaning is specified
Intertherm 50 - AkzoNobel
international.brand.akzonobel.comOct 30, 2017 · Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning. Abrasive Blast Cleaning Abrasive blast clean to Sa2½ (ISO 8501-1:2007) or SSPC-SP6. If oxidation has occurred between blasting and application of Intertherm 50, the surface should be reblasted to the specified visual standard.
Interthane 990 - AkzoNobel
marinecoatings.brand.akzonobel.comMay 25, 2016 · contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. SURFACE PREPARATIONS NEWBUILDING/MAJOR REFURBISHMENT Interthane 990 should always be applied over a recommended primer …
SSPC-SP1 Solvent Cleaning
d1wg3emhath1s.cloudfront.netSSPC-SP1 Solvent Cleaning The method of solvent cleaning is intended to remove “all visible oil, grease, soil, drawing and cutting compounds, and all other soluble contaminants from steel surfaces.” The specification calls for the removal of dust before solvent cleaning by the use of a stiff bristle brush.
Intergard 821 - AkzoNobel
marinecoatings.brand.akzonobel.comDec 04, 2015 · contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. SURFACE PREPARATIONS ANODE SHIELDS NEWBUILDING/MAJOR REFURBISHMENT Where necessary, remove weld spatter and smooth weld seams and sharp edges. Abrasive blast clean to Sa2½ (ISO 8501-1:2007). If oxidation has occurred between …