CONNECTOR AND RECEPTACLE WIRE/CABLE ASSEMBLY …
2 1. ASSEMBLY WARNINGS –READ THIS ENTIRE SECTION 1.1. WARNING – INSPECT WIRING, CHARGER PLUGS, AND MATING VEHICLE RECEPTACLES Inspect all wiring for cracking, wear and tear and damage along Charger output leads to Plug and along Vehicle Receptacle to Battery Pack.
Download CONNECTOR AND RECEPTACLE WIRE/CABLE ASSEMBLY …
Information
Domain:
Source:
Link to this page:
Documents from same domain
CONNECTOR AND RECEPTACLE WIRE/CABLE …
www.dpipower.com2 1. ASSEMBLY WARNINGS –READ THIS ENTIRE SECTION 1.1. WARNING – INSPECT WIRING, CHARGER PLUGS, AND MATING VEHICLE RECEPTACLES Inspect all wiring for cracking, wear and tear and damage along Charger
ACCUSENSE CHARGE SERIES ON/OFF BOARD …
www.dpipower.com3 simply plug in the DC cord set to activate the unit. The charger then automatically charges the battery, and also monitors the battery condition
Xcel / AccuSense CHARGE SERIES FULLY …
www.dpipower.com4 • The conductor with insulation having an outer surface that is green, with or without yellow stripe(s), is the equipment-grounding conductor.
General Chargers - Diversified Power International
www.dpipower.comEXTENSION CORDS FOR BATTERY CHARGERS Length of cord (feet): 25 50 100 150 AWG size of cord: 12 12 10 8 Provide adequate ventilation for the batteries and charger. The convection-cooled design requires an unobstructed flow of cooling air for proper operation. Keep all charger ventilation openings at least two
Related documents
Dell OptiPlex 9010/7010 Small Form Factor Owner's Manual
downloads.dell.comcables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.
5000 Series Owner's Manual - Dell
downloads.dell.comits pull-tab, not on the cable itself. Some cables have connectors with locking tabs or thumb-screws that you must disengage before disconnecting the cable. When disconnecting cables, keep them evenly aligned to avoid bending any connector pins. When connecting cables, make sure that the ports and connectors are correctly oriented and aligned.
Arista 400G Transceivers and Cables: Q&A
www.arista.comArista offers passive copper breakout cables in 400G and 200G versions. Both versions include breakouts from an OSFP / QSFP-DD port to 2x QSFP, 4x QSFP, and 8x SFP ports. The key differences between the 400G and 200G versions are: 1. The 400G cables are designed to carry 8x 50Gb/s PAM-4 electrical lanes, while the 200G cables are
COAXIAL CABLES - Axon’ Cable
www.axon-cable.comFLEXIBLE MINIATURE COAXIAL CABLES - Flexible miniature coaxial cables offering a good com-promise between a small diameter (e.g. < 0.2 mm) and a capacitance of 50 to 100 pF/m. - Laying up of more than 500 PICO-COAX® into MULTI-PICO-COAX® cables. - Manufacture of harnesses : MULTIPICO-COAX® cables can be terminated by different types of ...
Cisco SFP Modules for Gigabit Ethernet Applications Data …
www.cisco.comAPC connectors are not supported. All cables and cable assemblies used must be compliant with the standards specified in the standards section. ... SFP ports have LC-type connectors, and the minimum cable distance for all SFPs listed (multimode and single-mode fiber) is …
USB Type-C Connectors - Molex
www.content.molex.comUSB Type-C Connectors The expanded family of compact USB Type-C Connectors supports up to 5.0A current and 40 Gbps speeds, and offers waterproof, robust, reliable connectivity in ... non-Type-C USB cables Short mating length Provides space savings and design flexibility High-temperature nylon insert-mold receptacle housing Increases connector
Digilent Pmod Interface Specification
www.digilentinc.comIn general, Pmod peripheral modules can plug directly into connectors on the host controller board, or be connected to the controller board via six-pin or twelve-pin cables. Two six-pin peripheral modules can be connected to a single twelve-pin host connector via a twelve-pin to dual six-pin splitter cable.