Current Active Standards
Corrosion Protection of Steel and Concrete Structures July 2004, ed. rev. August 2010 : ... Field Methods for Retrieval and Analysis of Soluble Salts on Steel and Other Nonporous Substrates ... Guide to Evaluation of Slip and Fall Resistance of Flooring Surfaces . May 2015 .
Download Current Active Standards
Information
Domain:
Source:
Link to this page:
Documents from same domain
Good PaintinG Practice, SSPc PaintinG Manual, …
www.sspc.orgSSPC PRODUCTS CATALOG 3 www.sspc.org Here’s what you will find inside the SYSteMS and SPecificationS, SSPc PaintinG Manual, VoluMe 2 HOW tO USE SSPC StANDARDS, SPECIFICAtIONS, AND
SSPC QP2 Audit Evaluation Checklist Contractor: …
www.sspc.orgQP2 Audit Evaluation Checklist (11/10) Page 2 of16 AUTHORITY AND RESPONSIBILITY OF COMPETENT PERSONS Audit Item Number QP Number Required Information Rating
QP1 Audit Checklist - Society for Protective Coatings
www.sspc.orgQP1 Audit Checklist (MAR 2013) Page 3 of 25 Audit and Initial Application Item Number: Quality Procedure Reference Number: Audit Criteria: Rating
SSPC: The Society for Protective Coatings Using …
www.sspc.orgsing SSPC Coating aterial Standards October 1, 2014 1 SSPC: The Society for Protective Coatings Using SSPC Coating Material Standards Coating Selection
Painting Contractor Certification Program (PCCP) …
www.sspc.orgQP- 9 07/14 Page 1 of 18 Painting Contractor Certification Program (PCCP) QP–9 Audit Evaluation Checklist Standard Procedure for Evaluating the Qualifications of
SSPC QP1 APPLICATION, INSTRUCTIONS, AND PROGRAM …
www.sspc.orgapplying for SSPC QP1 Certification must demonstrate a history of compliance with QP1 quality and safety requirements. To be eligible for an initial QP1 audit, applicants must meet the following criteria: 1) Shall be a legal entity (e.g., incorporated, assigned a federal tax ID) under the
ID No. Title Latest Revision SURFACE PREPARATION
www.sspc.orgJul 09, 2012 · SSPC-SP 7/ NACE No. 4 Brush-Off Blast Cleaning January 2007 SSPC-SP 8 Pickling November 1982, ed. rev. November 2004 SSPC-SP 10/ NACE No. 2 Near White Metal Blast Cleaning January 2007 SSPC-SP 11 Power Tool Cleaning to Bare Metal November 2013 SSPC-SP 13/NACE No. 6 Surface Preparation of Concrete May 2018
Related documents
Hilti - 2011 Anchor Fastening Technical Guide
www.buildsite.comAnchor Fastening Technical Guide 1.0 Introduction 4 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en español 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 1.1 A bout Published Load Values The Anchor Fastening Technical Guide is intended to We passionately create enthusiastic …
CHAPTER 13: ENCAPSULATION
apps.hud.govamination and evaluation of coating systems are being conducted by the Massachusetts Depart-ment of Public Health and the Maryland De-partment of the Environment with funding from the U.S. Environmental Protection Agency (EPA). Some sites with interior and exterior coatings have been found to remain intact for up to 3 years. On the other hand, the
CORROSION GUIDELINES
dot.ca.govPRINCIPLES OF CATHODIC PROTECTION ... These guidelines outline the corrosion evaluation and recommendation aspects of site ... References to the test methods used for corrosion testing must be included on each page that presents the corrosion test results and analysis. Some variations (like a one-point
ANNUAL BOOK OF ASTM STANDARDS - Markit
global.ihs.comSection 3: Metals Test Methods & Analytical Procedures Volume 03.01: Metals -- Mechanical Testing; Elevated and Low-Temperature Tests; Metallography Volume 03.02: Corrosion of Metals; Wear and Erosion Volume 03.03: Nondestructive Testing Volume 03.04: Magnetic Properties Volume 03.05: Analytical Chemistry for Metals, Ores, and Related Materials:
ACI MANUAL OF CONCRETE PRACTICE INDEX—2015
img.equipmentworld.com222R-01 Reapproved 2010 Protection of Metals in Concrete Against Corrosion, Part 1 222.2R-14 Report on Corrosion of Prestressing Steels, Part 1 222.3R-11 Guide to Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, Part 1 223R-10 Guide for the Use of Shrinkage-Compensating Concrete, Part 1
HANDBOOK ON REPAIR AND REHABILITATION OF RCC …
theconstructor.org1) Manual on Planning and Design of Reinforced concrete multi-storeyed buildings – Vol. –I and Vol. –II. - 1976 2) Maintenance from Approach, Cause and Effect Study by Shri K S Narayanan 3) A Report of Documentation on Fire, Assessment of …
ICC-ES Evaluation Report ESR-2290 - James Hardie Pros
www.jameshardiepros.comESR- 2290 | Most Widely Accepted and Trusted Page 2 of 31 4.0 DESIGN AND INSTALLATION 4.1 Design: Walls: The maximum basic wind speeds for positive or negative transverse load resistance of HardieShingle™ (New HardieShingle®) panels, HardiePlank™ (Cemplank®, Prevail™, and RFC®) lap siding, Artisan® Lap Siding, and HardieShingle™ (New …
The Repair and Protection of Reinforced Concrete
www.sika.comEN 1504 – 7 Provides specifications for reinforcement corrosion protection EN 1504 – 8 Describes the quality control and evaluation of conformity for the manufacturing companies EN 1504 – 9 Defines the general principles for the use of products and systems, for the repair and protection of concrete
MATERIALS SELECTION - Standard
www.standard.no5.3 Corrosivity and corrosion protection 5.3.1 Corrosion allowance For carbon steel piping, a corrosion allowance of 3 mm shall be used, unless higher corrosion allowances are required. Recommendation: For submarine pipeline systems a total corrosion allowance of 10 mm is recommended as a general upper limit for use of carbon steel.