DE-5000 Portable, Full-Featured LCR Meter User and Service ...
To understand the ratio of resistance and reactance, it is important to consider two factors: quality factor (Q) and dissipation factor (D). Usually Q is used when measuring inductance and D is used when measuring capacitance. D is defined as the reciprocal of Q. Q = 1/D = tanΘ Q = Xs/Rs = 2πf Ls/Rs = ½πf CsRs
Download DE-5000 Portable, Full-Featured LCR Meter User and Service ...
Information
Domain:
Source:
Link to this page:
Documents from same domain
PT100 TEMPERATURE / RESISTANCE TABLE °C 0 1 2 3 4 5 6 7 …
ietlabs.compt100 temperature / resistance table °c 0 1 2 3 4 5 6 7 8 9 °c-200 18.4932-200-190 22.8031 22.3737 21.9439 21.5139 21.0834 20.6526 20.2215 19.7899 19.3580 18.9258 -190
Related documents
Surface Mount Multilayer Ceramic Chip Capacitors (SMD ...
content.kemet.comSee Insulation Resistance Limit Table (Rated voltage applied for 120 ±5 seconds at 25°C) 1 Regarding Aging Rate: Capacitance measurements (including tolerance) are indexed to a referee time of 48 or 1,000 hours. Please refer to a part number specific datasheet for referee time details.
Model 187 & 189
assets.fluke.com• Disconnect circuit power and discharge all high-voltage capacitors before testing resistance, continuity, diodes, or capacitance. • Use the proper terminals, function, and range for your measurements. • Before measuring current, check the meter’s fuses and turn power OFF to the circuit before connecting the meter to the circuit.
ASTROAI USER MANUAL DIGITAL MULTIMETER NOTE …
images-na.ssl-images-amazon.comNote: If you are measuring an unknown Resistance, set the range switch to the highest range and reduce it until a satisfactory reading is obtained. 3. If the resistance being measured is connected to a circuit, turn off power and discharge all capacitors before measurement. 4.
Instrument Transformers Application Guide
library.e.abb.com4.14 Coupling capacitors 74 4.15 CVTs as coupling capacitors 75 4.16 Measure harmonics with VTs 76 5. Design of current transformers 79 5.1 General 79 5.2 Hair-pin type (Tank type) 80 5.3 Cascade/Eye-bolt type 81 5.4 Top core type 81 5.5 Combined current-voltage type 82
Electrical Interview Questions & Answers visit www.eeekenya
www.eeekenya.com2. Why the capacitors works on ac only? Answer: Generally capacitor gives infinite resistance to dc components (i.e., block the DC components). It allows the ac components to pass through. 3. Explain the working principal of the circuit breaker? Answer: Circuit Breaker is one which makes or breaks the circuit. It has two contacts namely fixed
Electrical Components - Pearson
www.pearsonhighered.comCapacitors can be roughly checked by using an ohm-meter. The ohmmeter used in testing capacitors should be able to read a high resistance and have at least an R * 100 scale. To test the capacitor, disconnect it from the wiring and place the ohmmeter leads on the terminals, as shown in Figure 36-15 .
Film Capacitors - General technical information
www.tdk-electronics.tdk.comS Series resistance, due to contacts (leads, sprayed metal and film metallization) R P Parallel resistance, due to insulation resistance C Capacitance C, R S and L S are magnitudes that vary in the frequency domain (AC). R P is a magnitude defined in DC (insulation resistance). 2.2 Capacitance 2.2.1 Rated capacitance / measuring conditions
Metallized Polypropylene Film Capacitors DC-Link Capacitor
www.vishay.comMetallized Polypropylene Film Capacitors DC-Link Capacitor FEATURES • High performance DC filter •Low ESR ... Insulation resistance RC between leads, after 1 min > 10 000 s For UNDC ≤ 500 V measuring voltage 100 V For UNDC > 500 V measuring voltage 500 V Life time expectancy Useful life time: > 100 000 h at UNDC and 70 °C FIT: ...