DESIGN GUIDELINE 220020 HIGH PURITY WATER SYSTEMS
consisting of a basket strainer with a 1/64” mesh opening strainer element. Provide pressure gages across the strainer. Storage Tank(s) The A/E shall carefully evaluate storage tank size based on program requirements. Minimum tank sizes adequate to hold a 1/2 day’s worth of production are typical. Tanks shall be translucent with a bottom ...
Download DESIGN GUIDELINE 220020 HIGH PURITY WATER SYSTEMS
Information
Domain:
Source:
Link to this page:
Documents from same domain
DESIGN GUIDELINE 5.6 PARKING STRUCTURES
umaec.umich.eduArchitectural Design equirements ... Structure decks sh all be either cast -in-place reinforced concrete or constructed with precast double tees with a minimum 4” top of tee or any other tested and approved technology for parking ... panels except as required by to be fire rated. Fire rated door assemblies shall be factory Code
Electrical Acceptance Tests
umaec.umich.eduA 1,000 volt DC megger test and a turns ratio test shall be performed on CT's and PT's. The metering shall be calibrated. Engine-Generators and Automatic Transfer Switches . A continuity check and 1,000 volt DC megger test shall be performed on the generator
GROUNDING AND BONDING FOR ELECTRICAL
umaec.umich.eduGrounding systemconductors making up the grounding mat and associated ground risers, and/or for encasement in concrete shall be No. 4/0 AWG bare, stranded copper. Ground conductors for power distribution equipment,all end-use equipment and all branch circuits, shall be insulated stranded copper conductors, color coded greenor (a continuous)
Commissioning Plan
umaec.umich.eduThe Commissioning Plan is the vehicle by which the Cx process is planned and documented. The draft version of the Cx Plan for this project was produced by the Commissioning Authority (CxA). The Owner’s Commissioning Authority and the Contractor are responsible for developing the final Commissioning Plan and executing all commissioning activities.
Design Deliverables - Architecture Engineering and ...
umaec.umich.eduOn the "Design Deliverables" document, the Design Professional shall indicate the status of each required item (a check mark is interpreted to mean that an item has been included in the deliverables). On or attached to the "Design Deliverables" document, the Design Professional shall identify all items NOT included in the review package.
DESIGN GUIDELINE 230030 LABORATORY VENTILATION
umaec.umich.eduLABORATORY VENTILATION DG 230030 OCTOBER 2016 PAGE 1 OF 24 DESIGN GUIDELINE 230030 LABORATORY VENTILATION Information for mechanical design engineers as well as architects/lab planners regarding laboratory ventilation design at U-M, including but not limited to the following:
DESIGN GUIDELINE 5.2 ANIMAL FACILITIES
umaec.umich.edu4.7 SBA Building Access Control 6.0 DG 230030 - Laboratory Ventilation 6.0 DG 263000 - Engine-Generator System . Reference Documents: “Guide for Care and Use of Laboratory Animals” , promulgated by United States Department of Health and Human Services, and the Regulations of the Federal Animal Welfare Act 9, CFR Parts ,1 2 and 3
Related documents
Background information Year 7, unit 1: Mixing and separating
scienceweb.asta.edu.auor strainer) compared to the size of the particles being separated. The important thing to remember is that the holes in the filter must be smaller in size than the particles of the solid substance being separated. The term ‘filtering’ is generally used when the mixture contains a solid and a liquid, for example sand and water.
PRESSURE DROP CHARTS - WYE & BASKET STRAINERS
www.titanfci.comPRESSURE DROP CHARTS f WYE & BASKET STRAINERS TITAN TITAN FLOW CONTROL, INC. Tel: 910-735-0000 s Fax: 910-738-3848 s [email protected] www.titanfci.com 290 Corporate Drive s PO Box 7408 s Lumberton, NC 28358 TITAN FLOW CONTROL, INC. Cv CORRECTION FACTOR TABLE Centistokes (SSU) Perf. (Unlined) 20 MESH 40 MESH 60 MESH 80 MESH 100 MESH 120 MESH ...
SPEC TB Lav-Shield2 82202 - IPS Corp
ipsplumbingproducts.comstrainer assembly #100 E-Z Series (shown above right) for tubular and cast brass P-trap assemblies. #400W* Series(original design) for schedule 40 P-trap assemblies. Manufactured under one or more of the following U.S. or Canadianpatents. Other patents pending. 5,303,730 5,360,031 5,524,669 5,564,463 5,678,598 5,699,828 5,915,412