“Do It Right” User’s Guide
1. Slide fitting nut and ferrule back approximately ¾" from end of tubing. 2. If necessary, spray the entire assembly with LOCTITE® Primer. Allow to dry. NOTE: Primer is not required for brass parts. 3. Apply a thin coating of LOCTITE® Thread Sealant to …
Download “Do It Right” User’s Guide
Information
Domain:
Source:
Link to this page:
Documents from same domain
“When, Where & How” to Use LOCTITE Maintenance Products ...
www.useloctite.comAnaerobic adhesives and sealants were developed by the founder of LOCTITE Corporation, now Henkel Corporation, in 1953 and, since then, they have significantly evolved to meet the highest requirements of equipment manufacturers, maintenance and overhaul. Anaerobic adhesives and sealants are resins that convert from liquid to a tough
Related documents
Quicklub Lubrication Systems - Lincoln Industrial
www.lincolnindustrial.comStandard Compression Fittings for Steel or Nylon Tubing Model No. Description 241290 ¹⁄₄" tube x ¹⁄₈" NPT male straight fitting 241293 ¹⁄₄" tube x ¹⁄₈" NPT male 90° fitting Divider Valve Outlet Adapters for ¼" O.D. Steel or Nylon Tubing Compression-Style With Check Valve Model No. Description 68462 Ferrule …
Cooper Crouse-Hinds LIQUIDTIGHT FITTINGS
www1.crouse-hinds.comthe conduit until the ferrule threads engage the spirals in the conduit. The pins in the ferrule are locked inside the holes in the connector body, preventing the ferrule from turning. Tighten the nut against the connector. LiQuik Liquidtight Fittings — malleable iron, straight, non-insulated Catalog Number Trade Size KO Size Dimensions A B C ...
Valves, Fittings and Tubing - Autoclave
www.autoclave.comthis catalog) an advanced single ferrule fitting system called the QSS-Quick Set System. Designed to work with our Medium Pressure 316 cold worked S.S. and 2507 Super Duplex ™ instru-ment tubing, this 1/4” through 1” O.D. connection is utilized in our valves and fittings to provide a simple to install connection in all sizes up to 15,000 psi
HOSE BARB BRASS FITTINGS Hose Barb Fittings - Hayward …
www.haywardpipe.comCA360 Brass for Barstock fittings. CA377 Brass for Forged fittings. Note: These fittings are intended for use with hose clamp, similar type clamp or a crimped ferrule. • Assembly Instructions 1- Cut hose cleanly and squarely to length. 2- Slide clamp on hose. 3-Lubricate hose. Push hose on fitting until hose bottoms against stop ring or hex.
Gyrolok Fitting Locator 2 GYROLOK ® Tube Fittings
catalog.hoke.comend Fittings Controlled ferrule drive prevents end connection expansion, thus prolonging valve life and eliminating the need to use female-ended valves with separate fittings. Eliminates a possible leak path and extends valve life. Long product life and maximum value. Safety and economy. saFety
PRODUCT CATALOGUE - A&G Engineering
www.agengineering.com.ausize clamp ferrule blank seal seal seal seal mm body long cap epdm buna teflon viton ... wine fittings 9. nb pipe size size welded seamless approx.wgt inch mm o.d. wt 304/l 316/l 2205 304/l 316/l 2205 kg/mtr ...
Bussmann series 15.5 kV E-Rated medium voltage fuses for ...
www.eaton.com• Constructions available in ferrule, bolt-on and clip-lock, and specialty mount fuses for AMPGARD motor starters. ... end fittings) End fittings (disconnect Diameter Clip center Length Porcelain insulator only) Glass-polyester insulator CLE 15E–25E Single barrel Non-disconnect 95
Hydraulic Fittings Thread Guide - Green Line Hose
www.greenlinehose.comTwo-piece (separate stem and ferrule) crimp fi ttings for most hoses 8600… Interlock (internal skive) two-piece crimp fi ttings for spiral hoses 9600… One-piece skive crimp fi ttings for spiral hoses ... SAE and JIC Flare Fittings in hydraulic applications, while SAE adapters are …
Gaugeable Tube Fittings and Adapter Fittings (MS-01-140 ...
www.swagelok.com2 Tube Fittings TUBE FITTINGS Features Live-loaded, two-ferrule design. Easy to install. No torque is transmitted to tubing during installation. Swagelok® gap inspection gauge ensures sufficient pull-up upon initial installation. Two-Ferrule, Mechanical Grip Design The two ferrules separate sealing and tube gripping functions; each ferrule is optimized for its function.
Gaugeable Alloy 2507 Super Duplex Tube Fittings (MS-01 …
www.swagelok.comSwagelok alloy 2507 tube fittings utilize the same advanced geometry back ferrule design and patented ferrule hardening process as other Swagelok tube fittings, providing excellent vibration resistance and leak-tight gas seal. Alloy 2507 fittings are NORSOK M-630 and M-650 compliant as standard and are available in sizes from 1/4 to 3/4 in.