DUCTILE IRON PIPE - McWane
tapping, even in straight lines, doesn’taffect its integrity.And, once installed, Ductile Iron pipe is virtually maintenance free. The pipe is manufactured in 18- or 20-foot nominal laying lengths and 3- to 64-inch diameters in a range of standard pressure …
Download DUCTILE IRON PIPE - McWane
Information
Domain:
Source:
Link to this page:
Documents from same domain
14-24” RDGV METAL-SEATED ROTATING DISC ... - …
pe.mcwane.comDivision of McWane, Inc. 1021 EAST WATER STREET ELMIRA, NEW YORK 14901 THIS DRAWING AND ALL INFORMATION IS KENNEDY VALVE PROPERTY AND SHALL NOT BE USED, COPIED, OR REPRODUCED WITHOUT WRITTEN CONSENT.
3-12” RDGV METAL-SEATED ROTATING DISC ... - …
pe.mcwane.comDivision of McWane, Inc. 1021 EAST WATER STREET ELMIRA, NEW YORK 14901 THIS DRAWING AND ALL INFORMATION IS KENNEDY VALVE PROPERTY AND SHALL NOT BE USED, COPIED, OR REPRODUCED WITHOUT WRITTEN CONSENT.
![Untitled-1 [pe.mcwane.com]](/cache/preview/0/6/a/a/7/a/e/3/thumb-06aa7ae3820fc1a116eff00b799cf8bf.jpg)
Untitled-1 [pe.mcwane.com]
pe.mcwane.comdivision of mcwane inc. index service, roadway and valve boxes erie (arch) and minneapolis pattern service boxes 2 service box 3" service box 4 1/4" roadway box 5 1/4" valve box 7" valve box bibby visi n ane page . plug lid style service box small service & nor base & service box complete fig service @ &
THRUST RESTRAINT DESIGN FOR DUCTILE IRON PIPE
pe.mcwane.comDuctile Iron pipe and fittings are most often joined with push-on (Figure 1) or mechanical joints. Neither of these joints provides significant restraint against longitudinal separation other than the friction between the gasket and the plain end of the pipe or fitting.
DESIGN OF DUCTILE IRON PIPE - McWane
pe.mcwane.com§ AASHTO T-99, “Moisture Density Relations of Soils Using a 5.5 pound Rammer 12-in. Drop.” 150 300 400 500 700 30 45 60 90 150 0.235 0.210 0.189 0.157 0.128 E’ psi Bedding Angle degrees Kb x 0.108 0.105 0.103 0.096 0.085 FIGURE 1 Standard Laying Conditions for Ductile Iron Pipe Type 1* Flat-bottom trench.† Loose backfill. Type 2 Flat ...
Related documents
STANDARD SEWER AND WATER MAIN SPECIFICATIONS
www.nyc.govConnections For Flanged Tapping Valve Or Mechanical Joint Tapping Valve (Section 2.09) 20.10 Specifications For Corporation Stops And Quarter Bends (Section 2.10) II-3 20.11 Specifications For Trunk Main Work II-3 21.01 Definitions II-4 21.02 Vitrified Clay Pipe II-6 21.03 Cast Iron Pipe II-8 21.04 Cast Iron Soil Pipe II-9
PIPE SUPPORT HARDWARE
www.pipesupports.comPipe Clip Page 15 Figures 81, 81BRT, 81PT, 81SG Extension Ring Hanger Page 16 Figure 89 Riser Clamp Page 18 Figures 90, 90PT Split Ring Hanger, Double Tapping Page 19 Figures 91, 91Z Heavy Duty Three Bolt Pipe Clamp Pages 20, 21 Figures 100, 100SS Clevis Hanger Page 22 Figure 100DI Clevis Hanger for Ductile Iron Pipe Page 24 Figure 100EL ...
XIV. STANDARD WATER SPECIFICATIONS AND DETAILS …
charlottenc.govA. PIPE 1. Ductile Iron Pipe: Ductile iron pipe shall conform to the requirements of AWWA Standard C-151 and shall have a cement-mortar lining of standard thickness in accordance with AWWA C-104. Unless otherwise shown on the construction plans, all ductile iron pipe shall be furnished with push on joints in accordance with AWWA C-111.
UNDERGROUND PIPE SYSTEM INSTALLATION MANUAL
futurepipe.comWAVISTRONG® (H2O) WATER SERIES pipe standard lengths. Nominal Pipe Diameter (mm) Standard Pipe Length (m) 80 5 100 - 300 5 350 - 600 5 700 - 800 5 900 and above 5 Table 1-Standard Pipe Length This manual should be carefully read by the Contractor responsible for laying the pipes, as well as by the design Engineer. This information
DESIGN OF DUCTILE IRON PIPE - McWane
pe.mcwane.comWith more than five decades of outstanding field experience, Ductile Iron pipe is widely recognized as the industry standard for modern water and wastewater systems. ... tapping strength, flow characteristics, impact resistance, lining and joint integrity, and virtually all aspects of the material that can affect its performance.
Sutton Tools Tapping Drill Size Chart
www.aimsindustrial.com.au*Taper pipe threads of improved quality are obtained when the tapping hole is pre-formed using Sutton Taper Pipe Reamers. ... NATIONAL PIPE STRAIGHT (60º) Tap Size TPI Tapping Drill mm 1/8 27 8.6 1/4 18 11.3 3/8 18 14.5 1/2 14 18.0 THREAD FORMING (FLUTELESS TAPS) Tap Size T.P.I. Tapping Drill mm UNC #1 (.073) 64 1.7
Tapping Drill Sizes - ajhw.co.uk
www.ajhw.co.uk1 3/8 6 1 7/32 31.0 1 3/4 7 1 39/64 40.9 BSP British Standard Pipe 1 1/2 6 1 11/32 34.1 2 7 1 55/64 47.2 BA British Association 1 5/8 5 1 7/16 36.5 1 3/4 5 1 9/16 39.7 2 4.5 1 25/32 45.2 Metric Equivalents www ajhw.co.uk Tapping Drill Sizes British Imperial A.J.H. Computer Services BSW Metric Equivalents BSF Metric Equivalents BSP Metric ...
PVC Pipe—Design and Installation - American Water Works ...
www.awwa.orgDirect Tapping, 99 Saddle Tapping, 105 Tapping Sleeve and Valve, 107 Appendix A, Chemical Resistance Tables, 109 Appendix B, Flow Friction Loss Tables, 129 ... pipe manufactured in accordance with AWWA C900, Polyvinyl Chloride (PVC) Pres-sure Pipe and Fabricated Fittings, 4 In. Through 12 In.