ELECTRONICS INDUSTRIES Generic Requirements for Surface ...
Surface Mount Design and Land Pattern Standard Developed by the Surface Mount Land Patterns Subcommittee (1-13) of the Printed Board Design Committee (1-10) of IPC Users of this publication are encouraged to participate in the development of future revisions. Contact: IPC 3000 Lakeside Drive, Suite 309S Bannockburn, Illinois 60015-1219 Tel 847 ...
Download ELECTRONICS INDUSTRIES Generic Requirements for Surface ...
Information
Domain:
Source:
Link to this page:
Documents from same domain
Exigences et critères d’acceptabilité pour l ...
www.ipc.orgB.J. Franco, Honeywell Aerospace Richard Rumas, Honeywell Canada John Mastorides, Honeywell International William Novak, Honeywell International
A standard developed by IPC
www.ipc.orgIPC/WHMA-A-620B-S 2013 - June Space Applications Electronic Hardware Addendum to IPC/WHMA-A-620B Supersedes IPC/WHMA-A-620AS with Amendment 1 June 2012
Appendix B RoHS Substances and Exemptions List …
www.ipc.orgMarch 2011 IPC-1752A Appendix B RoHS Substances and Exemptions List The EU RoHS Directive continues to be updated over time. As these changes are made, the most current exemption list will
JOINT INDUSTRY GUIDE (JIG) - IPC
www.ipc.orgJOINT INDUSTRY GUIDE (JIG) Material Composition Declaration for Electrotechnical Products JIG-101 Ed 4.0 (Revision of JIG-101 Ed. 3.1, September 2010)
(Mechanical, Electrical, Environmental and Quality ...
www.ipc.orgIPC-9591 Performance Parameters (Mechanical, Electrical, Environmental and Quality/Reliability) for Air Moving Devices Developed by the Air Moving Devices Standard Subcommitte (9-81) of
Certification Quality Initiative User’s Guide v
www.ipc.orgCertification Quality Initiative User’s Guide v.2 IPC , i n c . 3000 L a k e s i d e D r i v e , S u i t e 309S B a n n o c k b u r n , I L 6 0 015
IPC Polcies and Procedure Manual (April 2017 …
www.ipc.orgPage | 2 IPC Professional Training and Certification Policies and Procedures v6 1 BACKGROUND. This Policy and Procedures (P&P ) document is applicable to IPC’s Professional Training and Certification Programs (hereinafter “Programs”), including lecture-based discrimination -skills
IPC-TM-650 TEST METHODS MANUAL
www.ipc.org1 Scope Moisture absorption can cause delamination or other damage in printed boards subjected to soldering heat. This test is a process control tool to determine both the bulk
Design and Assembly Process Implementation for …
www.ipc.orgIPC-7093 Design and Assembly Process Implementation for Bottom Termination SMT Components Developed by the IPC Bottom Termination Components (BTC) Task
ELECTRONICS INDUSTRIES Design and Assembly …
www.ipc.orgIPC-7095A Design and Assembly Process Implementation for BGAs Developed by the Device Manufacturers Interface Committee of IPC Users of this publication are encouraged to participate in the
Related documents
LT3080 - Adjustable 1.1A Single Resistor Low Dropout …
www.analog.comResistor Low Dropout Regulator The LT ®3080 is a 1.1A low dropout linear regulator that can be paralleled to increase output current or spread heat in surface mounted boards. Architected as a precision cur-rent source and voltage follower allows this new regulator to be used in many applications requiring high current,
XLSEMI Datasheet
www.nikom.bizPart Number Marking ID Lead Free Lead Free Packing Type XL6009E1 XL6009E1 Tube Package Temperature Range XL6009TRE1 XL6009E1 Tape & Reel XLSEMI Pb-free products, as designated with “E1” suffix in the par number, are RoHS compliant. Absolute Maximum Ratings（Note1） Parameter Symbol Value Unit Input Voltage Vin -0.3 to 42 V
LM2596 - 3.0 A, Step-Down Switching Regulator
www.onsemi.comD2PAK surface mount package. The other features include a guaranteed 4% tolerance on output voltage within specified input voltages and output load conditions, and 15% on the oscillator frequency. External shutdown is included, featuring 80 …
INSTALLATION INSTRUCTIONS PUSH BUTTON START SYSTEM
www.jegs.comrelays do not use internal diode or resistor snubbers. FOR ALL RELAYS: Pins 30 and 86 are connected to B+, 12VDC. Pin 85 is pulled low by the system to power the coil; pin 87 is the high current output which is enabled when the coil is powered. Pin 87A is not used. Form C Relay Relay Pinouts 2.
Power Metal Strip Resistors, Low Value (Down to 0.0005 Ω ...
www.vishay.com(1) Flame retardance test may not be applicable to some resistor technologies Notes • Part marking: value; tolerance: due to resistor size limitations some resistors will be marked with only the resistance value (1) For values above 0.1 Ω derate linearly to 80 % rated power at 0.5
Wirewound Resistors, Precision Power, Surface Mount
www.vishay.com(1) Flame retardance test may not be applicable to some resistor technologies Notes • Part marking: 1/2 W - DALE, value; 1 W - model, value, tolerance, date code; 2 W and 3 W - DALE, model, value, tolerance, date code (1) As of 1/1/2010, the WSC0001 and WSC0002 are molded with thermopl astic in lieu of epoxy. Reference PCN-DR-002-2009 and PCN ...
SF-1206S Series - Slow Blow Surface Mount Fuses
www.farnell.comn Slow blow thin film chip fuse for overcurrent protection n 3216 (EIA 1206) miniature footprint n Surface mount packaging for automated assembly n UL listed (UL 248-14) n RoHS compliant* and halogen free** Electrical Characteristics SF-1206S Series - Slow Blow Surface Mount Fuses *** Resistance value measured with less than 10 % of rated current.
SA602A Double-balanced mixer and oscillator
www.nxp.comA 22 k resistor from OSC_E (pin 7) to ground increases the DC bias current of the oscillator transistor. This improves the AC operating characteristic of the transistor and should help the oscillator to start. A 22 k resistor does not upset the other DC biasing internal to the device, but smaller resistance values should be avoided. a.