Engineering & Design Data
9 NOTE: Spears® recommends that Flow Velocities be maintained at or below 5 feet per second in large diameter piping systems (i.e. 6" diameter and larger) to minimize the potential for hydraulic shock. Refer to Spears® engineering section entitled "Hydraulic Shock" for additional information. Friction loss data based on utilizing mean wall dimensions to determine average
Download Engineering & Design Data
Information
Domain:
Source:
Link to this page:
Documents from same domain
Schedule 40 Fittings & Accessories Pipe Flanges
www.spearsmfg.comSchedule 40 Fittings & Accessories Pipe Flanges & Flange Bolt Kits Pipe Flanges Part Number Size Std Pk Mstr Ctn Disc Code Price Each …
TECHNICAL INFORMATION WEIGHTS & …
www.spearsmfg.com924 Visit our web site www.spearsmfg.com TECHNICAL INFORMATION WEIGHTS & DIMENSIONS PVC & CPVC Schedule 80 Fittings, …
STANDARDS & SPECIFICATIONS P100 Coupling
www.spearsmfg.comDWV PVC DWV Drain Waste Vent Fittings STANDARDS & SPECIFICATIONS Standards provide greater assurance of product performance and consistency, and are available to assist design engineers in system specification.
STANDARDS & SPECIFICATIONS Dimensions of …
www.spearsmfg.comBarbed Insert Fittings Barbed Insert Fittings STANDARDS & SPECIFICATIONS ASTM D 2609 Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe. Material
Schedule 80 PVC Industrial Products & Accessories …
www.spearsmfg.comSchedule 80 PVC Industrial Products & Accessories Schedule 80 PVC Industrial Pipe Part Number Size Std Pk Mstr Ctn Disc Code …
Item prices may have changed from those shown in …
www.spearsmfg.comPVC & CPVC Metric Fittings, Unions & Valves SPEARS® QUALITY POLICY It is the policy and objective of Spears® Manufacturing Company to produce a superior quality product suitable for its intended use, with
PLASTIC PIPE FITTINGS & VALVES - Spears Mfg Co …
www.spearsmfg.com92 LabWaste™ CPVC Corrosive Waste Drainage System Solvent Cement Welded System • Pipe - Cement - Fittings • Sizes 1-1/2" - 12" …
FS-5 RED - Spears Manufacturing, PVC & CPVC …
www.spearsmfg.comSPEARS® MANUFACTURING COMPANY FS-5 RED TECHNICAL SPECIFICATIONS Low VOC CPVC Solvent Cement PRODUCT: Spears ® FlameGuard FS-5 …
V-4-1211 1211 Part 3 68-94 8x10.5 - Spears Mfg Co …
www.spearsmfg.comBUTTERFLY VALVES Sample Engineering ... * See “BUTTERFLY VALVE ACCESSORIES” section for details of individual products. ... (.18) 17 (.12) 11 (.08)-0-18…
Schedule 80 PVC Industrial Products & Accessories ...
www.spearsmfg.comSchedule 80 PVC Industrial Products & Accessories Butterfly Valves ... See Butterfly Valve Accessories & Repair Kits Section for
Related documents
Water Calc. Worksheet INFORMATION REQUIRED TO ... - …
dsps.wi.gov7- Determine pressure loss due to friction in inch diameter water service. Water service piping material is Pressure loss per 100 ft. = X (decimal equivalent of service length, i.e. 65 ft = 0.65) Subtract value of "7" Subtotal 8- Determine pressure loss or gain due to elevation, Subtract value of "8" (multiply the value of # 2 above by .434)
DAMAGE TO FOUNDATIONS FROM EXPANSIVE SOILS
web.mst.edufriction adhesion below the zone of drying; and, second, to resist upward movement when the surface soils become wet and begin to swell. Successive drought years have demonstrated that the zone of seasonal fluctuation can extend much deeper than previously believed. Piers extending to depths of six feet can withstand
SECTION 7 – CULVERTS - Round Rock, Texas
www.roundrocktexas.govFriction loss is the energy required to overcome the roughness of the culvert material and is expressed as: hf= (29n2L/R1.33)(V2/2g) (Eq. 7-10) where n = Manning's coefficient L = Length of culvert, feet R = Hydraulic radius, feet
F D C Air Flow and Air Friction - Thermaflex
www.thermaflex.netLoss of .15 In.H20 for 15 feet. A second method for using charts is: Supposing Air Velocity is known at 1000 FPM through 6”ID Thermaflex M-KE.In this case, use Chart No.1 and locate the diagonal 1000 FPM line at intersection with 6”ID line;then read downward vertically to Friction Loss line and net loss as .8 In.H20 per 100 feet. Supposing ...