Engineering Design Data - PVC Pipe Supplies
Therefore, 2" schedule 80 PVC pipe is acceptable for this application. The total pressure at any time in a pressure-type system (operating plus surge or water hammer) should not exceed 150 percent of the pressure rating of the system. Table I - C-Surge Wave Constant Pipe Size PVC CPVC (in.) Sch.40 Sch.80 Sch.40 Sch.80 1/8 34.7 41.3 32.9 39.4
Download Engineering Design Data - PVC Pipe Supplies
Information
Domain:
Source:
Link to this page:
Documents from same domain
Physical Properties of PVC CPVC Pipe - PVC Pipe Supplies
pvcpipesupplies.comThe physical properties shown above pertain to GF Harvel PVC (SDR Series,Schedule 40,80 & 120) and GF Harvel CPVC (Schedule 40 and 80) industrial pipe. The physical properties shown for CPVC pipe are considered general CPVC physical properties.GF Harvel utilizes several CPVC compounds for the production of different CPVC product lines.
PVC and CPVC Pipe Charts
pvcpipesupplies.comPVC and CPVC Pipes - Schedule 40 Nominal Pipe Size (inches) Outside Diameter (inches) Minimum Wall Thickness (inches) Inside Diameter*) (inches) Weight (lb/ft) PVC CPVC 14 14.000 0.438 13.124 11.80 16 16.000 0.500 15.000 15.43 PVC and CPVC Pipes - Schedule 80 Nominal Pipe Size (inches) Outside Diameter (inches) Minimum Wall Thickness (inches)
Related documents
SEWER TESTING AND INPECTION - wefppvl.org
www.wefppvl.orgthe Contractor shall conduct a line acceptance test using low-pressure air testing. For ductile iron pipelines test in accordance with the applicable requirements of ASTM C924. For PVC pipelines test in accordance with ASTM F1417 -98 and UBPPA UNI-B-6. For gasketed joint plastic composite pipe (Truss Pipe), it is often desirable to begin and finish
C-900/C-905 - Northern Pipe
www.northernpipe.comC-900 standard specification for polyvinyl chloride water distribution pipe. The integral bell joint system meets the requirements of ASTM D-3139 and utilizes an elastomeric seal meeting the specification defined in ASTM F-477. Northern Pipe Products AWWA C-900 Pressure Pipe for potable water carries the NSF Standard 14, the
PVC C900 High Pressure Water Pipe - CPS Distributors
cpsdistributors.comInstallation Guide for PVC Water Pipe. Product C900 is suitable for use as a pressure conduit. Expansion and contraction are accommodated by a properly assembled gasketed joint. Each bell section meets the same pressure capacity requirements as the pipe. Standard laying lengths are 20 feet (plus or minus 1 inch). Pipe Stiffness Pressure Class ...
API 650 TANKS - Engineers Australia
www.engineersaustralia.org.au30mm Ǿ PVC pipes are installed at 4 angular locations to provide weep holes leaking product. Tank earthing is facilitated by connecting the tank shell to the rebar. The ring wall is back filled with select fill and compacted to 95% mdd. 5/27/2009 FUEL TANK & PIPE 12 Diesel is sprayed on the fill to prevent corrosion of the
I.P.S. PRESSURE - JM Eagle
www.jmeagle.comPressure surges in PVC pipe (12454) of different dimension ratios in response to a 1 fps (0.3 mps) instantaneous flow velocity change are shown in Table 2. TABLE 2 DESIGN TABLE FOR PVC PIPE-PRESSURE SURGE VS. DIMENSION RATIO SDR PRESSURE SURGE psi kPa 13.5 20.2 139 14 19.8 137 17 17.9 123 18 17.4 120 21 16.0 110 25 14.7 101 26 14.4 99 32.5 12.8 ...
INSTALLATION INSTRUCTIONS - Lennox
www.lennox.comalso include a 2" diameter PVC street elbow, which is shipped on the blower deck in the heating compartment. G61MPV−60D−135 units are shipped with a 3" to 2" PVC reducing elbow. Canadian Installations Only − Replace the provided 2" street elbow shipped with the G61MPV−60C−110 and G61MPV−60C−111 units with 2" street elbow Y0162. Re-