FASTENER REFERENCE GUIDE
(Hex up to 1-1/2 & Heavy Hex 1-1/2 and over) Notes 1. “Compatible” denotes commercially available nut having suitable mechanical properties and dimensional configuration or style which will make it possible to obtain the desired bolt load. Higher strength nuts or nuts of equal strength may be a
Download FASTENER REFERENCE GUIDE
Information
Domain:
Source:
Link to this page:
Documents from same domain
Mechanical Properties of Externally Threaded …
www.fastenal.comMechanical Properties of Externally Threaded Fasteners ... Similar to B7 except heat-treated to ... Mechanical Properties of Externally Threaded Fasteners ...
Safety Data Sheet - Fastenal
www.fastenal.comSafety Data Sheet Revision Number: 004.0 Issue date: 08/28/2014 IDH number: 235028 Product name: LOCTITE LB 771 NICKEL GRADE ANTI-SEIZE known as Nickel Grade Anti-Seize Page 1 of 6
Flat Washer, Thin, Nylon - Fastenal
www.fastenal.comPage 1 of 1 Fastenal Product Standard REV-02 Date: July 18, 2017 FW.THIN.NYL Flat Washer, Thin, Nylon The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order.
Pipe Flange, Class 150, Threaded, Raised Face, Plain …
www.fastenal.comPage 1 of 1 Fastenal Product Standard REV-01 Date: November 19, 2011 FLG.150.RF.THRD.P Pipe Flange, Class 150, Threaded, Raised Face, Plain Finish The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order.
Torque-Tension Relationship for Metric Fasteners
www.fastenal.comThe torque values can only be achieved if nut (or tapped hole) has a proof load greater than or equal to the bolt's minimum ultimate tensile strength. Clamp loads …
FAST Guide Electrical Safety - Fastenal
www.fastenal.comFAST Guide to Electrical Safety Common Electrical Hazards Written Electrical Safety Program Stop At Your Local Store Need some extra wire to finish up an electrical ...
Screw Thread Design - Fastenal – Industrial Supplies ...
www.fastenal.comA screw thread is defined as a ridge of uniform section in the form of a helix on either the external ... The higher the class number, the tighter the fit. The ‘A’ designates ... cut threading will be full-size from the fillet under the head to the end of the bolt. Producing cut .
Ladder Safety - fastenal.com
www.fastenal.com200 lbs. Light Duty - Occasional or household Type III 225 lbs. Medium Duty - Commercial painters, office settings and maintenance Type II 250 lbs. Heavy Duty - Industrial settings, for utility work ... Ladder Safety FMPM-7180 Fast+Talk Newsletter • KV • 5.18. Created Date:
Mechanical Properties of Externally Threaded Fasteners
www.fastenal.comCompatible denotes commercially available nut having suitable mechanical properties and dimensional configuration or style which will make it possible to obtain the desired bolt load. Higher strength nuts or nuts of equal strength may be a suitable substitute provided bolt standard allows.
Cushioned Clamps Cushion Rolls Toggle Hangers Fasteners ...
www.fastenal.com1–274 For pricing and availability, contact your local Fastenal store or visit fastenal.com Fasteners Cushioned Clamps, Cushion Rolls, Rooftop Pipes & Equipment Supports…
Related documents
Mechanical Properties of Externally Threaded Fasteners
www.fastenal.comAug 25, 2009 · Proof Load Stress (psi) 8 Medium carbon or alloy steel, quenched & tempered 150,000 5 Carbon steel 1/4 - 4 Over 1 – 1 1/2 Grade ASTM A194-Grade 2H Heavy Hex Material Nominal Size(in.) FNL Grade 9 Thick Hex Nut ASTM A194-Grade 8 Heavy Hex AISI 304 1/4 – 1 1/2 Carbon Steel ASTM A563-Grade A Heavy Hex Medium Carbon Steel Carbon Steel …
FASTENERS MASONRY FASTENER TECHNICAL DATA AND …
www.kljack.comThe stress at which a material exhibits a specified deviation from the proportionality of stress to strain. The deviation is expressed in terms of strain, and in the offset method, usually a strain of 0.2 percent is specified. PROOF LOAD The point to which a material may be stressed without evidence of permanent deformation. HARDNESS