FASTENER REFERENCE GUIDE
A 316 Stainless Steel used for high temperature applications. This material has been carbide solution treated in the finished condition. ASTM A193/A193M B8 Class 2 3/4 & under over 3/4 to 1 over 1 to 1-1/4 over 1-1/4 to 1-1/2 125,000 115,000 105,000 100,000 100,000 80,000 65,000 50,000 C35 A 304 Stainless Steel similar to
Download FASTENER REFERENCE GUIDE
Information
Domain:
Source:
Link to this page:
Documents from same domain
Mechanical Properties of Externally Threaded …
www.fastenal.comMechanical Properties of Externally Threaded Fasteners ... Similar to B7 except heat-treated to ... Mechanical Properties of Externally Threaded Fasteners ...
Safety Data Sheet - Fastenal
www.fastenal.comSafety Data Sheet Revision Number: 004.0 Issue date: 08/28/2014 IDH number: 235028 Product name: LOCTITE LB 771 NICKEL GRADE ANTI-SEIZE known as Nickel Grade Anti-Seize Page 1 of 6
Flat Washer, Thin, Nylon - Fastenal
www.fastenal.comPage 1 of 1 Fastenal Product Standard REV-02 Date: July 18, 2017 FW.THIN.NYL Flat Washer, Thin, Nylon The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order.
Pipe Flange, Class 150, Threaded, Raised Face, Plain …
www.fastenal.comPage 1 of 1 Fastenal Product Standard REV-01 Date: November 19, 2011 FLG.150.RF.THRD.P Pipe Flange, Class 150, Threaded, Raised Face, Plain Finish The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order.
Torque-Tension Relationship for Metric Fasteners
www.fastenal.comThe torque values can only be achieved if nut (or tapped hole) has a proof load greater than or equal to the bolt's minimum ultimate tensile strength. Clamp loads …
FAST Guide Electrical Safety - Fastenal
www.fastenal.comFAST Guide to Electrical Safety Common Electrical Hazards Written Electrical Safety Program Stop At Your Local Store Need some extra wire to finish up an electrical ...
Screw Thread Design - Fastenal – Industrial Supplies ...
www.fastenal.comA screw thread is defined as a ridge of uniform section in the form of a helix on either the external ... The higher the class number, the tighter the fit. The ‘A’ designates ... cut threading will be full-size from the fillet under the head to the end of the bolt. Producing cut .
Ladder Safety - fastenal.com
www.fastenal.com200 lbs. Light Duty - Occasional or household Type III 225 lbs. Medium Duty - Commercial painters, office settings and maintenance Type II 250 lbs. Heavy Duty - Industrial settings, for utility work ... Ladder Safety FMPM-7180 Fast+Talk Newsletter • KV • 5.18. Created Date:
Mechanical Properties of Externally Threaded Fasteners
www.fastenal.comCompatible denotes commercially available nut having suitable mechanical properties and dimensional configuration or style which will make it possible to obtain the desired bolt load. Higher strength nuts or nuts of equal strength may be a suitable substitute provided bolt standard allows.
Cushioned Clamps Cushion Rolls Toggle Hangers Fasteners ...
www.fastenal.com1–274 For pricing and availability, contact your local Fastenal store or visit fastenal.com Fasteners Cushioned Clamps, Cushion Rolls, Rooftop Pipes & Equipment Supports…
Related documents
SAE steel grades - Wikipedia, the free encyclopedia
li.mit.eduJul 10, 2012 · steel due to its increased resistance to chloride corrosion compared to type 304. 316 is often used for building nuclear reprocessing plants. 316L is an extra low carbon grade of 316, generally used in stainless steel watches and marine applications, as well exclusively in the fabrication of reactor pressure vessels for
Section S - EMJ
www.emjmetals.comThe weights shown would be accurate if steel and aluminum could always be produced to exact size, but this is seldom possible in commercial practice. Accuracy of dimensions, particularly of hot rolled steel products, ... 11/32.0263 .316 3.79 6.32 3/8.0313 2.376 4.51 7.52 13/32.0368 .441 5.29 8.82 7/16.0426 .512 6.14 10.23 15/32.0489 .587 7.05 11.75
FITTINS Pipe Fittings - Swagelok
www.swagelok.com316 stainless steel SS Carbon steel S Brass B 6-Moly 6Mo Alloy 625 625 Alloy 825 825 Alloy 2507 2507 Materials Material Standards Plating and Coating To resist corrosion, all carbon steel fittings are treated with an electrodeposited zinc plating. Material Bar Stock Forgings 316 stainless steel ASTM A276, ASME SA479, EN 1.4401