FASTENER REFERENCE GUIDE
3. ASTM A194 2H heavy hex nuts may be substituted for ASTM A563 DH heavy hex nuts. 4. Grade 2 requirements for sizes 1/4 through 3/4 in apply only to bolts and screws 6 in. and shorter in lengths. For bolts and screws longer than 6 in. Grade 1 requirements shall apply. 307A 307B A325 A449 BC BD A490 H - K G 9
Download FASTENER REFERENCE GUIDE
Information
Domain:
Source:
Link to this page:
Documents from same domain
Mechanical Properties of Externally Threaded …
www.fastenal.comMechanical Properties of Externally Threaded Fasteners ... Similar to B7 except heat-treated to ... Mechanical Properties of Externally Threaded Fasteners ...
Safety Data Sheet - Fastenal
www.fastenal.comSafety Data Sheet Revision Number: 004.0 Issue date: 08/28/2014 IDH number: 235028 Product name: LOCTITE LB 771 NICKEL GRADE ANTI-SEIZE known as Nickel Grade Anti-Seize Page 1 of 6
Flat Washer, Thin, Nylon - Fastenal
www.fastenal.comPage 1 of 1 Fastenal Product Standard REV-02 Date: July 18, 2017 FW.THIN.NYL Flat Washer, Thin, Nylon The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order.
Pipe Flange, Class 150, Threaded, Raised Face, Plain …
www.fastenal.comPage 1 of 1 Fastenal Product Standard REV-01 Date: November 19, 2011 FLG.150.RF.THRD.P Pipe Flange, Class 150, Threaded, Raised Face, Plain Finish The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order.
Torque-Tension Relationship for Metric Fasteners
www.fastenal.comThe torque values can only be achieved if nut (or tapped hole) has a proof load greater than or equal to the bolt's minimum ultimate tensile strength. Clamp loads …
FAST Guide Electrical Safety - Fastenal
www.fastenal.comFAST Guide to Electrical Safety Common Electrical Hazards Written Electrical Safety Program Stop At Your Local Store Need some extra wire to finish up an electrical ...
Screw Thread Design - Fastenal – Industrial Supplies ...
www.fastenal.comA screw thread is defined as a ridge of uniform section in the form of a helix on either the external ... The higher the class number, the tighter the fit. The ‘A’ designates ... cut threading will be full-size from the fillet under the head to the end of the bolt. Producing cut .
Ladder Safety - fastenal.com
www.fastenal.com200 lbs. Light Duty - Occasional or household Type III 225 lbs. Medium Duty - Commercial painters, office settings and maintenance Type II 250 lbs. Heavy Duty - Industrial settings, for utility work ... Ladder Safety FMPM-7180 Fast+Talk Newsletter • KV • 5.18. Created Date:
Mechanical Properties of Externally Threaded Fasteners
www.fastenal.comCompatible denotes commercially available nut having suitable mechanical properties and dimensional configuration or style which will make it possible to obtain the desired bolt load. Higher strength nuts or nuts of equal strength may be a suitable substitute provided bolt standard allows.
Cushioned Clamps Cushion Rolls Toggle Hangers Fasteners ...
www.fastenal.com1–274 For pricing and availability, contact your local Fastenal store or visit fastenal.com Fasteners Cushioned Clamps, Cushion Rolls, Rooftop Pipes & Equipment Supports…
Related documents
Suggested Assembly Torque Values - Nuts and Bolts
www.copperstate.comGenerally the full effort of an ironworker with a ordinary spud wrench is sufficient to tighten the nuts on anchor bolts. ... Heat Treated Alloy Steel, 4140/4142: 92 minimum 81 minimum ... Grade 105 = Red. All Thread Rod & All Thread Stud Materials When galvanizing high strength studs such as B7 & F1554-105, caution should be used as there is a ...
API Specification 20E
mycommittees.api.orgAlloy and Carbon Steel Bolting for Use in the Petroleum and Natural Gas Industries ... machined studs; machined bolts, screws and nuts; ... to be done to confirm quality of heat treated condition and insure freedom from heavily banded microstructure. Banding has been implicated in …
Standard Specification for Carbon Structural Steel1
dickeysteel.comA 307 Specification for Carbon Steel Bolts and Studs, 60 000 psi Tensile Strength A 325 Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength A 325M Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength [Metric] A 500 Specification for Cold-Formed Welded and Seamless
Standard Specification for Carbon Steel Bolts, Studs, and ...
fpg-co.comcomponents (bolts and nuts) shall be coated by the same zinc-coating process and the supplier’s option is limited to one process per item with no mixed processes in a lot. 5. Chemical Composition 5.1 Grade A and B bolts, studs, and threaded rod shall have a heat analysis conforming to the requirements specified in