Fastener Specifications (LS3) - Pace Performance
Feb 16, 2017 · A/C Drive Belt Tensioner Pulley to A/C Drive Belt Tensioner Retaining Bolt 50Y 37lbft A/C Drive Belt Tensioner to A/C Compressor Bracket Retaining Bolt 22Y 16lbft A/C Suction/Discharge Pipe Pad to A/C Compressor Retaining Bolt 16Y 12lbft Air Cleaner Inlet Duct to Throttle Body Hose Clamp 7Y 62lbin Automatic Transmission Cooler Pipe Clamp to A/C
Download Fastener Specifications (LS3) - Pace Performance
Information
Domain:
Source:
Link to this page:
Documents from same domain
350 HO Engine (12486041) Specifications
paceperformance.comLike all small block V-8. engines produced since 1986, the 350 HO engine has a 3.00” diameter flywheel flange bolt pattern. Sma ll block V-8. engines produced from 1958 through 1985 had a 3.58” diameter flywheel flange bolt pattern.
ZZ4/FB385 (12561727) Short Block Specifications
paceperformance.comengine is used for the ZZ4 and FB385 GMPP Crate Engines and does not include a camshaft, lifters, timing chain, cam sprocket, crankshaft sprocket, balancer, oil pan, flexplate or front cover. Just add all the parts to complete this engine from GMPP such as cylinder heads, camshaft and valvetrain, intake,
Fastener Specifications - Pace Performance
paceperformance.comFeb 16, 2017 · Specification Metric (English) Fuel Injection Fuel Rail Bolt 25Y (18lbft) Fuel Injection Fuel Rail Crossover Pipe Bolt 10Y (89lbin) Fuel Injection Fuel Rail Crossover Pipe Fitting 28Y (21lbft) Fuel Pump Bolt 25Y (18lbft) Fuel Pump Lifter Follower Guide Bolt 25Y (18lbft) Generator Bracket Bolt 50Y (37lbft)
Fastener Specifications - Pace Performance
paceperformance.comFeb 27, 2017 · Fastener Tightening Specifications Application Specification Metric English Accessory Drive Belt Idler Pulley Bolt 50Y 37lbft ... M11 Bolts in Sequence 90degrees Cylinder Head Bolts – Second Design – Final Pass all M11 Bolts in Sequence 70degrees Document ID: 1275636 Page 2 of 6
Related documents
Chain Tensioner - Tsubaki
tsubaki.ca(Tensioner is a swing type unit.) 3) Temporarily tighten the tensioner with two bolts. At this time, adjust with a shim, etc., so that the center of the idler sprocket and roller chain are aligned. (Fig. 6) 3) Push in on the chain with the tensioner and, if the amount of slack is appropriate (δ), tighten the nut and anchor the tensioner.
Fastener Specifications - Pace Performance
paceperformance.comFeb 27, 2017 · Accessory Drive Belt Tensioner Bolt 50Y 37lbft Air Conditioning (A/C) Compressor and Condenser Hose Bolt 27Y 20lbft A/C Drive Belt Idler Pulley Bolt 50Y 37lbft A/C Drive Belt Tensioner Bolt 25Y 18lbft Air Injection Reaction (AIR) Pipe-to-Exhaust Manifold Bolts 20Y 15lbft AIR Right Side Pipe Bracket-to-Cylinder Head Bolt 20Y 15lbft
SERVICE MANUAL - SHIMANO
si.shimano.comchain tensioner: 6.5 to 10 mm When installing the hub to the frame, the chain guard may come off, so check that the chain guard is securely installed so that it will not come off. If installation is incomplete, noise may be generated. Chain guard
Date: Jun-2016 Service Bullet,in
static.nhtsa.govTensioner spring in timing chain guide may be "short" not fully seating into guide pivot end. Cycling Oil Pump Control Valve will not cause changes in oil pump response. 1) Short spring not reaching the pivot. Replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump.
First Extended - Assurant
www.assurant.combelt tensioner, intake and exhaust manifolds, flywheel, balance shafts, harmonic balancer and retainer bolt, crankshaft pulley, valve covers, oil pan, engine oil cooler hoses, oil filter adapter/housing, engine oil sending unit, engine mounts, water pump, temperature sending unit, thermostat and housing, expansion (freeze) plugs, fuel supply pump,
2012 Scheduled Maintenance Intervals - Audi USA
www.audiusa.comRibbed V Belt and Tensioner – check condition and replace if necessary l R8, R8 Spyder only l R8, R8 Spyder only Ribbed V Belt – check condition, replace if necessary. Check tension of belt drive with manual tensioner and retension if necessary l 75K only: TT RS, V6 FSI, 3.0L V6 TFSI (rear belt), 2.0L TFSI, 5.2L V10 FSI, 4.2L V8 FSI only
Emergency Response Guide - Tesla, Inc.
www.tesla.comSRS control unit within 10 seconds of an airbag or pre-tensioner deployment. AIRBAG INFLATION CYLINDERS 16. SEAT BELT PRE-TENSIONERS Pre-tensioners are located at the bottom of the B-pillars, as outlined in red. Warning: The SRS control unit has a backup power supply with a discharge time of approximately ten seconds. Do not touch the