Fastener Specifications - Pace Performance
Feb 16, 2017 · Camshaft Position(CMP) Sensor Wire Harness Bolt 10Y (7lbft) Camshaft Retainer Bolt – TORX Head Bolt 15Y (11lbft) Charge Air Cooler Cover Ball Stud 10Y (89lbin) Charge Air Cooler Cover Bolts 10Y (89lbin) Charge Air Cooler Cover Double Ended Stud 10Y (89lbin) Charge Air Regulator Solenoid Valve Bolt 10Y (89lbin)
Download Fastener Specifications - Pace Performance
Information
Domain:
Source:
Link to this page:
Documents from same domain
350 HO Engine (12486041) Specifications
paceperformance.comLike all small block V-8. engines produced since 1986, the 350 HO engine has a 3.00” diameter flywheel flange bolt pattern. Sma ll block V-8. engines produced from 1958 through 1985 had a 3.58” diameter flywheel flange bolt pattern.
ZZ4/FB385 (12561727) Short Block Specifications
paceperformance.comengine is used for the ZZ4 and FB385 GMPP Crate Engines and does not include a camshaft, lifters, timing chain, cam sprocket, crankshaft sprocket, balancer, oil pan, flexplate or front cover. Just add all the parts to complete this engine from GMPP such as cylinder heads, camshaft and valvetrain, intake,
Fastener Specifications (LS3) - Pace Performance
paceperformance.comFeb 16, 2017 · A/C Drive Belt Tensioner Pulley to A/C Drive Belt Tensioner Retaining Bolt 50Y 37lbft A/C Drive Belt Tensioner to A/C Compressor Bracket Retaining Bolt 22Y 16lbft A/C Suction/Discharge Pipe Pad to A/C Compressor Retaining Bolt 16Y 12lbft Air Cleaner Inlet Duct to Throttle Body Hose Clamp 7Y 62lbin Automatic Transmission Cooler Pipe Clamp to A/C
Fastener Specifications - Pace Performance
paceperformance.comFeb 27, 2017 · Fastener Tightening Specifications Application Specification Metric English Accessory Drive Belt Idler Pulley Bolt 50Y 37lbft ... M11 Bolts in Sequence 90degrees Cylinder Head Bolts – Second Design – Final Pass all M11 Bolts in Sequence 70degrees Document ID: 1275636 Page 2 of 6
Related documents
550-870, 550-870K, 550-871, 550-871K, 550-872, & 550-872K ...
documents.holley.comJun 09, 2020 · 1 553-115 Includes harness to connect directly to CAN connector 10 Output Harness 1 558-491 Shutdown, Electric Fan #1 Output, and/or Mates to Input/Output connector on Main Wiring Harness and can be used for A/C Electric Fan #2 Output. 11 Main Harness and Ignition Adapter 1 558-490
November 2021, Volume 23, No. 21 TechLine Connect …
gm-techlink.comreference circuit 548 (J114). An additional three-wire splice has been added to the low reference circuit 548 (BK/GN). The three-wire splice is located in the main branch of the engine wiring harness above the EVAP purge pump assembly. Open the engine wiring harness to access the three-wire splice and inspect each leg for broken wire strands.
Instructions for the Vertical and Lateral Alignment of ...
www.bendix.comWhen mounting a radar sensor, the wire harness connector should always point down. The radar sensor assembly . is mounted to the front of the vehicle using an adjustable bracket. This adjustable bracket allows for the radar sensor to be properly aimed laterally and vertically to maximize Wingman Advanced system performance.
RIELLO 40 SERIES - Weil-McLain
www.weil-mclain.comThe air tube and drawer assembly are shipped in a carton separate from the burner chassis. Choose the proper air tube length to obtain the tube insertion for the specific installation. A) Remove the AIR TUBE and BURNER CHASSIS from their respective cartons. B) Remove the DRAWER ASSEMBLY (1) from inside the AIR TUBE by loosening the screw (2).