Fastener Specifications - Pace Performance
Feb 16, 2017 · Evaporative Emission Canister Purge Solenoid Valve Bolt 10Y (89lbin) Flywheel Inspection Cover Bolt 10Y (89lbin) Flex Plate to Torque Converter Fastener 60Y (44lbft) Fuel Feed Pipe Fitting 28Y (21lbft) Fuel Injection Fuel Rail Fuel Pressure Sensor 33Y (24lbft) Document ID: 4283190 Page 7 of 10
Download Fastener Specifications - Pace Performance
Information
Domain:
Source:
Link to this page:
Documents from same domain
350 HO Engine (12486041) Specifications
paceperformance.comLike all small block V-8. engines produced since 1986, the 350 HO engine has a 3.00” diameter flywheel flange bolt pattern. Sma ll block V-8. engines produced from 1958 through 1985 had a 3.58” diameter flywheel flange bolt pattern.
ZZ4/FB385 (12561727) Short Block Specifications
paceperformance.comengine is used for the ZZ4 and FB385 GMPP Crate Engines and does not include a camshaft, lifters, timing chain, cam sprocket, crankshaft sprocket, balancer, oil pan, flexplate or front cover. Just add all the parts to complete this engine from GMPP such as cylinder heads, camshaft and valvetrain, intake,
Fastener Specifications (LS3) - Pace Performance
paceperformance.comFeb 16, 2017 · A/C Drive Belt Tensioner Pulley to A/C Drive Belt Tensioner Retaining Bolt 50Y 37lbft A/C Drive Belt Tensioner to A/C Compressor Bracket Retaining Bolt 22Y 16lbft A/C Suction/Discharge Pipe Pad to A/C Compressor Retaining Bolt 16Y 12lbft Air Cleaner Inlet Duct to Throttle Body Hose Clamp 7Y 62lbin Automatic Transmission Cooler Pipe Clamp to A/C
Fastener Specifications - Pace Performance
paceperformance.comFeb 27, 2017 · Fastener Tightening Specifications Application Specification Metric English Accessory Drive Belt Idler Pulley Bolt 50Y 37lbft ... M11 Bolts in Sequence 90degrees Cylinder Head Bolts – Second Design – Final Pass all M11 Bolts in Sequence 70degrees Document ID: 1275636 Page 2 of 6
Related documents
BENDIX , AD-IS AND AD-IP AIR DRYER PURGE VALVE …
n0c357rmy1njbuit2friqwu.blob.core.windows.netCarefully ease the purge valve assembly into position using a gentle twisting motion. Do not force the purge piston, as serious damage may be caused to the seals. Make certain the purge valve assembly is fully seated against the air dryer body. 5. Secure the purge valve assembly in the air dryer using the retaining ring (5).
Aftertreatment Purge Air Valve Air Supply Line Routing for ...
static.nhtsa.govTitle: Aftertreatment Purge Air Valve Air Supply Line Routing for both Cummins ISX SCR Engines and N13 with SCR Engines Applies To: ProStar, TransStar , PayStar, 9900i. ISX Cummins SCR, N13 SCR DESCRIPTION Proper AFT Purge Valve air line routing. POSSIBLE FAULT CODES SPN 3490 FMI 7 Cummins Fault 3225 SERVICE PROCEDURE N13 with SCR
B36M ENGINE -FUEL TANK VENT (PURGE) VALVE: LIMITED ...
static.nhtsa.govB36M ENGINE -FUEL TANK VENT (PURGE) VALVE: LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILEAGE MODEL Note: The “Model” information above is for informational purposes only, it is not the only deciding factor. ELIGIBLE VEHICLES To determination a vehicle’s eligibility and to confirm this coverage applies, always perform a VIN-specific
Masoneilan* 35002 Series Camflex* II - Valves
valves.bakerhughes.comThe Camflex II valve is a heavy-duty, automatic-throttling control valve that incorporates the following features: • The flangeless body rating is a rugged ANSI Class 600. ... • The actuator linkage (purge option available) is totally enclosed). Table of Contents
DM-TL (DIAGNOSIS MODULE - TANK LEAKAGE)
www.princeton.eduThe change over valve is open during all other periods of oper-ation allowing the fuel system to “breath” through the inlet filter (similar to the full down stroke of the current vacuum operated LDP). DC MOTOR LDP INACTIVE -- NORMAL PURGE VALVE OPERATION In it’s inactive state the pump motor and the change over valve of the DC Motor LDP are
Bleed Valves and Purge Valves (MS-01-62;rev O;en …
www.swagelok.comPurge Valve PTFE Ball The Swagelok purge valve with PTFE ball provides leak-tight shutoff with finger pressure and features a removable cap for easy ball replacement. Pressure Rating: 200 psig at 100°F (13.7 bar at 37°C) Temperature Rating: 350°F (176°C). To order a Swagelok purge valve with PTFE ball, add -TFE to the ordering number.
WYJ - Walbro
www.walbro.comPURGE BULB UMBRELLA CHECK VALVE WYJ AT START POSITION (PURGE) Some WYJ carburetors have as an option a purge system, This purge system allows the customer to purge the metering system of air and replace it with fuel for easier starting. WYJ STARTING PROCEDURE By depressing the purge bulb 4-5 times, air is forced through the umbrella …