Fastener Specifications - Pace Performance
Feb 16, 2017 · Sequence 60degrees Cylinder Head Bolt • Cylinder Head Bolts - Internal Hex – LH Cylinder Head forwardmost fastener - First Pass in Sequence ... Reusable Threaded Fastener Tightening Specifications Application Specification Metric (English) Document ID: 4283190 Page 5 of 10
Download Fastener Specifications - Pace Performance
Information
Domain:
Source:
Link to this page:
Documents from same domain
350 HO Engine (12486041) Specifications
paceperformance.comLike all small block V-8. engines produced since 1986, the 350 HO engine has a 3.00” diameter flywheel flange bolt pattern. Sma ll block V-8. engines produced from 1958 through 1985 had a 3.58” diameter flywheel flange bolt pattern.
ZZ4/FB385 (12561727) Short Block Specifications
paceperformance.comengine is used for the ZZ4 and FB385 GMPP Crate Engines and does not include a camshaft, lifters, timing chain, cam sprocket, crankshaft sprocket, balancer, oil pan, flexplate or front cover. Just add all the parts to complete this engine from GMPP such as cylinder heads, camshaft and valvetrain, intake,
Fastener Specifications (LS3) - Pace Performance
paceperformance.comFeb 16, 2017 · A/C Drive Belt Tensioner Pulley to A/C Drive Belt Tensioner Retaining Bolt 50Y 37lbft A/C Drive Belt Tensioner to A/C Compressor Bracket Retaining Bolt 22Y 16lbft A/C Suction/Discharge Pipe Pad to A/C Compressor Retaining Bolt 16Y 12lbft Air Cleaner Inlet Duct to Throttle Body Hose Clamp 7Y 62lbin Automatic Transmission Cooler Pipe Clamp to A/C
Fastener Specifications - Pace Performance
paceperformance.comFeb 27, 2017 · Fastener Tightening Specifications Application Specification Metric English Accessory Drive Belt Idler Pulley Bolt 50Y 37lbft ... M11 Bolts in Sequence 90degrees Cylinder Head Bolts – Second Design – Final Pass all M11 Bolts in Sequence 70degrees Document ID: 1275636 Page 2 of 6
Related documents
TORQUE SPECIFICATIONS - JustAnswer
ww2.justanswer.comJun 14, 2009 · (1) For 1999 7.4L installation specifications, see appropriate procedure under CYLINDER HEAD under REMOVAL & INSTALLATION. Apply GM Sealant (1052080) to head bolt threads. (2) Tighten bolts in sequence. See Fig. 5. 4.3L V6, 5.0L, 5.7L & 7.4L V8 - VINS [W,X,M,R,J] -1999 GMC Suburban K1500 Page 3 of 7 6/14/2009
TORQUE SPECIFICATIONS Application Ft. Lbs (N.m)
ww2.justanswer.comFeb 05, 2010 · Fig. 10: Cylinder Head Tightening Sequence Courtesy of FORD MOTOR CO. Page 6 of 12 2/4/2010. Fig. 11: Exhaust Manifold Tightening Sequence (Right Side) Courtesy of FORD MOTOR CO. Page 7 of 12 2/4/2010. Fig. 12: Exhaust Manifold Bolt …
Caterpillar 3406 Engine Service Manual - Jensales
www.jensales.comct-s-eng340670 ccaatteerrppiillllaarr service manual 3406 diesel engine s/n 70v1 & up this is a manual produced byjensales inc.without the authorization of caterpillar or it’s successors.caterpillar and it’s successors are not responsible for the …
Fastener Specifications (LS3) - Pace Performance
paceperformance.comFeb 16, 2017 · Fastener Tightening Specifications Application Specification Metric English ... Cylinder Head to Engine Block Retaining Bolt (M8) - in sequence 30Y 22lbft Cylinder Head to Engine Block Retaining Bolt (M11) • First Pass in sequence 30Y 22lbft • Second Pass in sequence +90Degrees
Service Bulletin 09-010
static.nhtsa.gov49. Reinstall the cylinder head cover, tightening the bolts in three steps. In the final step, torque all bolts in sequence to . 12 N·m (8.7 lb-ft). 50. Reinstall the EVAP canister purge valve bracket. 51. Reinstall the engine oil dipstick and reconnect the breather hose and the brake booster vacuum hose. 52.
Installation Manual For ISM/ISM02/ISM07 M11/M11 Plus …
parts.jacobsvehiclesystems.comand hand tighten following the sequence in Fig. 13. complete the sequence by tightening the capscrews to 60 lb.-ft. (81 n•m). FIG. 11 FIG. 12 FIG. 13 Section 3: Brake Installation FRONT 1 4 7 5 3 2 6 16 8 14 15 12 9 13 10 11 REAR MODEL 411, C, D, E