Fastener Specifications - Pace Performance
Feb 16, 2017 · Single Use Threaded Fastener/Component Tightening Specifications Application Specification Metric (English) Note: All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. Automatic Transmission Flex Plate Bolt • First Pass: 15Y (133lbin) 30Y (22lbft) Document ID: 4283190 Page 2 of 10
Download Fastener Specifications - Pace Performance
Information
Domain:
Source:
Link to this page:
Documents from same domain
350 HO Engine (12486041) Specifications
paceperformance.comLike all small block V-8. engines produced since 1986, the 350 HO engine has a 3.00” diameter flywheel flange bolt pattern. Sma ll block V-8. engines produced from 1958 through 1985 had a 3.58” diameter flywheel flange bolt pattern.
ZZ4/FB385 (12561727) Short Block Specifications
paceperformance.comengine is used for the ZZ4 and FB385 GMPP Crate Engines and does not include a camshaft, lifters, timing chain, cam sprocket, crankshaft sprocket, balancer, oil pan, flexplate or front cover. Just add all the parts to complete this engine from GMPP such as cylinder heads, camshaft and valvetrain, intake,
Fastener Specifications (LS3) - Pace Performance
paceperformance.comFeb 16, 2017 · A/C Drive Belt Tensioner Pulley to A/C Drive Belt Tensioner Retaining Bolt 50Y 37lbft A/C Drive Belt Tensioner to A/C Compressor Bracket Retaining Bolt 22Y 16lbft A/C Suction/Discharge Pipe Pad to A/C Compressor Retaining Bolt 16Y 12lbft Air Cleaner Inlet Duct to Throttle Body Hose Clamp 7Y 62lbin Automatic Transmission Cooler Pipe Clamp to A/C
Fastener Specifications - Pace Performance
paceperformance.comFeb 27, 2017 · Fastener Tightening Specifications Application Specification Metric English Accessory Drive Belt Idler Pulley Bolt 50Y 37lbft ... M11 Bolts in Sequence 90degrees Cylinder Head Bolts – Second Design – Final Pass all M11 Bolts in Sequence 70degrees Document ID: 1275636 Page 2 of 6
Related documents
SAE and Metric Fastener Torque Specifications
manuals.gogenielift.com8 SAE and Metric Fastener Torque Specifications Metric Plain and Zinc Plated Hex and Socket Head Cap Screws TORQUE CHART - METRIC PLAIN AND ZINC PLATED HEX HEAD AND SOCKET HEAD CAP SCREWS. Class 4.6 . hex head cap screw: Class 8.8 hex head cap screw. DRY. LUBED. DRY: LUBED. SIZE: THREAD.
RECOMMENDED ASSEMBLY TORQUES
www.steelmasters.co.nzClass 4.6 ISO Metric Coarse Pitch Bolts & Screws Bolt Tension Recommended Corresponding to Assembly 65% of Proof Load Torque kN Nm 0.19 0.06 0.31 0.12 0.50 0.25 To convert kN to lbf: Multiply kN by 224.809 To convert Nm to lbft: Multiply Nm by 0.737562 0.73 0.44 1.29 1.00 2.08 2.1 2.94 3.5
Maintenance Manual 1 Preventive Maintenance and Lubrication
graphicvillage.orgFastener Torque 203 Inspecting the Transmission for Leaks and Damage Drain and Replace the Oil. pg. pg. ... 238 Trailer Lubrication Intervals and Specifications ... Studs and Nuts 243 Installing Double-Ended Metric Wheel Studs with 3/4-16 and M22 x 1.5 Threads Onto Hub and Rotor Assemblies on Axles Equipped with Meritor Air Disc Brake Model ADB ...
KT715-KT745 Service Manual - Kohler Engines
www.kohlerengines.comTORQUE SPECIFICATIONS3,5 KT715 KT725 KT730 KT735 KT740 KT745 Crankcase Breather Assembly Outer Cover Stud Outer Cover Hex Nut 6.2 N·m (55 in. lb.) into new hole 4.0 N·m (35 in. lb.) into used hole 1.3 N·m (11.5 in. lb.) Oil Drain Plug 13.6 N·m (10 ft. lb.) Cylinder Head Head Bolt Fastener (torque in 2 increments) fi rst to 22.6 N·m (200 ...
Tolerancing in ISO - Concordia University
users.encs.concordia.caThread specifications ... • Pitch is measured in millimeters for metric thread and indicated along ... • Some special cases (where the torque may loosen the fastener) may require Left hand threads • If Left hand threads are necessary it is indicated in the drawing
SELF-CLINCHING STUDS AND PINS - PennEngineering
www.pemnet.comMaterial and finish specifications -PAGE 17 Installation -PAGES 18 - 29 Performance data -PAGES 30 ... location of the mating fastener during assembly and protects the first thread of the stud during nut ... Unified C ±.005 E ±.010 B Nom. Metric C ±0.13 E ±0.25 B nom. Thread Size (2) Transitional Length to Full Thread Thread Size (2 ...
SELF-LOCKING FASTENERS - PennEngineering
www.pemnet.com• Thread locking torque performance is equivalent to applicable NASM25027 specifications. • LA4 floating fasteners are specifically designed to be installed into stainless steel sheets. To meet national aerospace standards and to obtain testing documentation, product must be ordered to US NASM45938/11 specifications.